Bedienungsanleitung Brandt WTC1015K Waschmaschine

Bedienungsanleitung

- 3 -

Removing the transport clamps from your machine see diagrams D1-D2-D3

1 - Remove the washing machine from its plinth (check that the wedge



supporting the motor is not still inserted in the machine)

(

Diagram

D1.➀

)

2 - Remove the 4 screws



with a screwdriver

(Diagram

D1.➁

)

3 - Remove the cross clamp



by removing the 2 screws



(Diagram

D1.➂

)

using a 10 or 13mm spanner (depending on the model).

(Ensure that you remove the two plastic braces fixed on the cross

clamp at the same time as the clamp itself).

Replace the screws



in their initial positions.

4 -



You must block off the two holes using the hole covers provided



(supplied in the accessories bag)

(Diagram

D1.➃

)

5 - Remove the drum-tank assembly locking wedge

(Diagram

D2

)

.

To do this:

- Lift the lid on the machine

- Remove wedge



- Remove wedge



by turning it a quarter turn

- Release the drum doors, locked in the lower position, by pressing

down on both eaves simultaneously.

6 -



Remove the pipe support collars

➀

You must block off the

holes revealed with the hole covers

➁

supplied in the accessories

bag

(Diagram

D3

)

.

Connecting the cold water supply

Connect the supply hose

(Diagram

D5

)

:

- At one end to the connection on the back of the machine

- On the other end to a tap fitted with a threaded end 20mm dia. x

27 (3/4 BSP).

If you use a self-piercing tap, the useful aperture must have a

minimum diameter of 6mm.

Water supply:

- Minimum water pressure: 0.07 MPa or 0.7 bar

- Maximum water pressure: 1 MPa or 10 bars

Draining away the waste water

Fit the hose bracket provided inside your machine to the end of the

drain hose and then connect the hose

(Diagram

D6

)

:

• Either, temporarily, over a sink or a bathtub.

• Or permanently to a ventilated U-bend.

If your installation does not have a ventilated U-bend, check that the

connection is not sealed. In fact, to avoid any waste water flowing

back into the machine, you are strongly recommended to leave an

air gap between the machine’s drain hose and the drainpipe.

In any case, the drain hose bracket must be placed at a height of 65

to 90cm higher than the base of the machine.



Ensure that the drain hose is tied firmly in place with cord to avoid

the bracket coming loose during draining and causing a flood.

The waste water can be drained away to the ground provided that

the drain hose passes through a point 65 to 90cm higher than the

base of the machine.



For your safety, you must comply with the instructions below.

Electrical supply

(Diagram

D7

)

• Before connecting your machine, you must ensure that your

installation’s electrical characteristics match those of your machine

(see the details provided on the information plate affixed to the back

of the machine).

• The electrical installation must comply with the prevailing standards

and the Electricity Board’s regulations in the country concerned,

particularly as regards Earthing and installation in shower rooms.

We cannot be held responsible for any incident caused by the

machine being incorrectly earthed.



Advice on the electrical installation of your machine

• Do not use an extension lead, adapter or multiple socket.

• Never cut out the Earth wire.

• The socket must be readily accessible but out of the reach of children.

If in any doubt, please contact your installer.

Installing your machine

see diagram

D4

Connecting your machine

see diagrams

D5-D6-D7



BEFORE USING THE MACHINE IN ANY WAY, YOU MUST FIRST PERFORM THE FOLLOWING OPERATIONS.

These comprise removing all the components designed to immobilise the drum in your machine during transport.

These so-called “releasing” operations are necessary for your machine to operate correctly and to conform to the prevailing safety

standards.

If they are not carried out completely, this could cause severe damage to your machine while it is operating.



We would recommend that you keep all the locking components since

these must be refitted if you must subsequently transport your machine

again.

All these components, just like all the components in your machine,

are made of recyclable materials and it is useful to bear this in mind

when you eventually come to dispose of your machine at the end of

its useful life.



Your machine has been scrupulously checked before it left the factory.

You may therefore notice a little water still remaining in the tank or the

products box.

Mounting it on castors:

If your machine is equipped with removable castors, you will be able

to move it quite easily.

To mount it on castors, swivel the lever on the bottom of the

machine from the right to the far left

(Diagram

D4

)

.



The machine must not rest on the “front” castors while it is

operating: remember to return the lever to its initial position.

Levelling the machine:

Use a spirit level to check that the floor is horizontal: maximum

slope 2°, i.e. a discrepancy of approximately 1cm over the width

and of 1.5cm over the depth of the machine.

Your machine’s surroundings:



If you are installing your machine next to another machine or a unit,

we recommend that you leave a gap between them to allow for

air circulation.



We also strongly recommend that you do NOT:

- Install your machine in a damp, poorly ventilated room.

- Install your machine in an area where it could be subject to water

splashes.

- Install your machine on a carpeted floor.

If you cannot avoid doing this, please take every precaution to avoid

blocking air circulation at the bottom of the machine in order to

ensure that the internal components are well ventilated.

Your machine conforms to European Directives EEC/73/23 (Low

Voltage Directive) and EEC/89/336 (Electromagnetic Compatibility)

as modified by Directive EEC/93/68.



On any new installation (following a move or resale, etc.), the

machine must be connected using new hoses. The old hoses must

not be reused.

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr Brandt WTC1015K Waschmaschine zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, Brandt zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres Brandt WTC1015K Waschmaschine in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für Brandt Waschmaschinen
Weitere Anleitungen von Waschmaschinen

Häufig gestellte Fragen zu Brandt WTC1015K Waschmaschine

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

Brandt WTL1261K Waschmaschine

Bedienungsanleitung

Brandt WTM0911K Waschmaschine

Bedienungsanleitung

Brandt WM700 Waschmaschine

Bedienungsanleitung

Brandt WFH1011 Waschmaschine

Bedienungsanleitung

Brandt WBD1114U Waschmaschine

Bedienungsanleitung

Brandt WTM0911N Waschmaschine

Bedienungsanleitung

Brandt WTM1021S Waschmaschine

Bedienungsanleitung

Brandt WFH1476D Waschmaschine

Verwandte Kategorien