Bedienungsanleitung Makita DMR106 Radio

Bedienungsanleitung

7

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

• To remove the battery cartridge, withdraw it from the

tool while sliding the button on the front of the cartridge

or pressing the buttons on both sides of the cartridge.

Installing or removing Cluster battery

cartridge (Fig. 6 & 7)

• To insert the battery cartridge, align the tongue on the

battery cartridge with the grove in the housing and slip

it into place.

• To remove the battery cartridge, take the battery out of

the terminal while pressing the buttons on the side of

cartridge.

Return the battery compartment locker to the original

position.

Reduced power, distortion, “stuttering sound” or when

both low battery sign and “POWERFAIL” appear on

the display are all the signs that the main battery pack

needs to replace.

Note:

The battery pack can’t be charged via the supplied AC

power adaptor.

When low battery sign appears and an “EMPTY”

keeps on flashing is the time to replace the back up

batteries.

Using the soft bended rod antenna (Fig. 8)

Straight up the soft bended rod antenna as shown in the

figure.

Using Supplied AC power adaptor (Fig. 9)

Remove the rubber protector and insert the adaptor plug

into the DC socket on the left side of the radio. Plug the

adaptor into a standard mains socket outlet. Whenever

the adaptor is used, the battery pack is automatically

disconnected. The AC adaptor should be disconnected

from the main supply when not in use.

Note:

When your radio has any interference in AM band by its

adaptor, please move your radio away from its AC adaptor

over 30 cm.

Operating your radio – Scan tuning AM/

FM

1. Press the Power button to switch on your radio.

2. Press the Source button to select AM or FM radio

mode.

3. Press and hold the Tuning control knob to carry out

an auto-tune. Your radio will scan up the AM/FM band

from the currently displayed frequency and will stop

scanning automatically when it finds a station of

sufficient strength.

4. After a few seconds the display will update. The

display will show the frequency of the signal found.

5. To find other station, press and hold the Tuning control

knob as before.

6. When the end of the waveband is reached your radio

will recommence tuning from the opposite end of the

waveband.

7. Rotate the Tuning control knob to adjust the sound

level as required.

Note:

• While adjusting the volume, make sure the FM/AM is

NOT flashing on the screen.

• If AM/FM is flashing on the screen, it allows you to

tune the stations manually (see the section of

“Manual tuning

– AM/ FM” for more detail).

8. To switch off your radio press the Power button .

Manual tuning – AM/FM

1. Press the Power button to switch on your radio.

2. Press the Source button to select AM or FM radio

mode.

3. Press the Tuning control knob and you will see the

FM or AM is flashing on the display.

Note:

• FM/AM will flash approx. 10 seconds. Within this

period, only manual tuning is allowed.

• If volume adjustment is desired while FM/AM is

flashing, press the Tuning control knob to stop the

flash and you can rotate the Tuning control knob to

adjust sound level.

4. Rotate the Tuning control knob to tune to a station.

5. When the end of the waveband is reached your radio

will recommence tuning from the opposite end of the

waveband.

6. Use the Tuning control knob to adjust the sound

level as required.

Presetting stations in AM/FM mode

There are 5 preset stations each for AM and FM radio.

They are used in the same way for each waveband.

1. Press the Power button to switch on your radio.

2. Press the Source button to select the desired

waveband. Tune to the required radio station as

previously described.

3. Press and hold the required Preset button (1 to 5)

until the display shows “P4” for

example after the frequency. The station will be stored

using the preset number. Repeat this procedure for

the remaining presets as you wish.

4. Preset stations which have already been stored may

be overwritten by following the above procedure if

required.

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr Makita DMR106 Radio zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, Makita zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres Makita DMR106 Radio in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für Makita Radios
Weitere Anleitungen von Radios

Häufig gestellte Fragen zu Makita DMR106 Radio

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

Makita DMR105 Radio

Bedienungsanleitung

Makita DMR102 Radio

Bedienungsanleitung

Makita DMR109 Radio

Bedienungsanleitung

Makita DMR107 Radio

Bedienungsanleitung

Makita BMR100 Radio

Bedienungsanleitung

Makita BMR102 Radio

Bedienungsanleitung

Makita DMR108 Radio

Bedienungsanleitung

Makita BMR104 Radio

Verwandte Kategorien