Bedienungsanleitung Makita 6960D Schlagschrauber

Bedienungsanleitung

Installing or removing bit

CAUTION:

Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit.

Use only the driver bit or socket bit shown in the figure below.

Do not use any other driver bit or socket bit.

To install the bit, pull the sleeve in the direction of the arrow and insert the bit into the sleeve as far as it will go. Then

release the sleeve to secure the bit. (Fig. 3)

To remove the bit, pull the sleeve in the direction of the arrow and pull the bit out firmly.

CAUTION:

•

This tool is designed to drive wood screws. Do not use this tool to drive machine screws or bolts. The tool may be

damaged.

•

If the bit is not inserted deep enough into the sleeve, the sleeve will not return to its original position and the bit will

not be secured. In this case, try re-inserting the bit according to the instructions above.

NOTE:

If the bit is not inserted deep enough into the sleeve, the sleeve will not return to its original position and the bit will not

be secured. In this case, try re-inserting the bit according to the instructions above.

Switch action (Fig. 4)

CAUTION:

Before inserting the battery cartridge into the tool, always

check to see that the switch trigger actuates properly and

returns to the ‘‘OFF’’ position when released.

To start the tool, simply pull the trigger. Tool speed is

increased by increasing pressure on the trigger. Release

the trigger to stop.

Reversing switch action (Fig. 5)

CAUTION:

•

Always check the direction of rotation before operation.

•

Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation before

the tool stops may damage the tool.

•

When not operating the tool, always set the reversing

switch lever to the neutral position.

This tool has a reversing switch to change the direction of

rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for counter-

clockwise rotation. When the switch lever is in the neutral

position, the switch trigger cannot be pulled.

Installing set plate (Fig. 6)

Always install the set plate when using battery cartridges

1200, 1202 or 1202A. Install the set plate on the tool with

the screw provided as shown in Fig. 6.

Characteristics of Cordless Oil-Impulse Driver

The Makita Cordless Oil-Impulse Driver is a hydraulically

operated impact tool using oil viscosity to produce

impacts. Since oil viscosity changes with the temperature,

be aware of the following two points when operating the

tool.

1) If the tool itself is cold, it may take longer to set screws

because of the low fastening torque when you begin

operation. After fastening about ten screws, however,

the fastening torque will become normal.

2) The tool can overheat, causing a failure or hand burn

if you operate it continuously for long hours. Let the

tool cool off for more than 30 minutes before chang-

ing batteries during a long, continuous job.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and the battery

cartridge is removed before carrying out any work on the

tool.

Replacement of carbon brushes (Fig.7&8)

Replace carbon brushes when they are worn down to the

limit mark. Both identical carbon brushes should be

replaced at the same time.

To maintain product safety and reliability, repairs, main-

tenance or adjustment should be carried out by Makita

Authorized Service Center.

5

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr Makita 6960D Schlagschrauber zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, Makita zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres Makita 6960D Schlagschrauber in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für Makita Schlagschrauber
Weitere Anleitungen von Schlagschrauber

Häufig gestellte Fragen zu Makita 6960D Schlagschrauber

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

Makita TD090D Schlagschrauber

Bedienungsanleitung

Makita BTW120 Schlagschrauber

Bedienungsanleitung

Makita BTD132 Schlagschrauber

Bedienungsanleitung

Makita BTW072 Schlagschrauber

Bedienungsanleitung

Makita TD0100 Schlagschrauber

Bedienungsanleitung

Makita DTW1005 Schlagschrauber

Bedienungsanleitung

Makita BTD125 Schlagschrauber

Bedienungsanleitung

Makita TW011G Schlagschrauber

Verwandte Kategorien