Bedienungsanleitung Makita 6960D Schlagschrauber

Bedienungsanleitung

3. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

4. Hold the tool firmly.

5. Wear ear protectors.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge (Fig. 1)

•

Always switch off the tool before insertion or removal of

the battery cartridge.

•

To remove the battery cartridge, withdraw it from the

tool while pressing the buttons on both sides of the

cartridge.

•

To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If not, it may accidentally fall out

of the tool, causing injury to you or someone around

you.

•

Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Charging (Fig. 2)

Your new battery cartridge is not charged. You will need to charge it before use. Use the fast charger Model DC1411

to charge the battery cartridge.

Plug the fast charger into the proper AC voltage source. The charging light will flash in green color. Insert the battery

cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective

markings on the fast charger. Insert the cartridge fully into the port so that it rests on the charger port floor. When the

battery cartridge is inserted, the charging light color will change from green to red and charging will begin. The charging

light will remain lit steadily during charging. When the charging light color changes from red to green, the charging cycle

is complete. If you leave the battery cartridge in the charger after the charging cycle is complete, the charger will switch

into its ‘‘trickle charge (maintenance charge)’’ mode which will last approximately 24 hours. After charging, unplug the

charger from the power source. Refer to the table below for the charging time.

Battery type Capacity (mAh) Number of cells

Charging time with

fast charger DC1411

1222 2,000 10 Approx. 60 min.

1233 2,200 10 Approx. 65 min.

1234 2,600 10 Approx. 75 min.

1235 3,000 10 Approx. 90 min.

CAUTION:

•

The fast charger Model DC1411 is for charging Makita battery cartridge. Never use it for other purposes or for other

manufacturer’s batteries.

•

When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time,

it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the

battery cartridge fully after discharging it completely and recharging a couple of times.

•

If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location

exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a

while. Charging will begin after the battery cartridge cools. The battery cartridge will cool faster if you remove the

battery cartridge from the fast charger.

•

If the charging light flashes alternately in green and red color, a problem exists and charging is not possible. The

terminals on the charger or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged.

Trickle charge (Maintenance charge)

If you leave the battery cartridge in the charger to prevent spontaneous discharging after full charge, the charger will

switch into its ‘‘trickle charge (maintenance charge)’’ mode and keep the battery cartridge fresh and fully charged.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely discharged.

Always stop tool operation and charge the battery cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room temperature at 10°C – 40°C (50°F – 104°F).

Let a hot battery cartridge cool down before charging it.

4. Charge the Nickel Metal Hydride battery cartridge when you do not use it for more than six months.

4

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr Makita 6960D Schlagschrauber zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, Makita zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres Makita 6960D Schlagschrauber in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für Makita Schlagschrauber
Weitere Anleitungen von Schlagschrauber

Häufig gestellte Fragen zu Makita 6960D Schlagschrauber

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

Makita TD090D Schlagschrauber

Bedienungsanleitung

Makita BTW120 Schlagschrauber

Bedienungsanleitung

Makita BTD132 Schlagschrauber

Bedienungsanleitung

Makita BTW072 Schlagschrauber

Bedienungsanleitung

Makita TD0100 Schlagschrauber

Bedienungsanleitung

Makita DTW1005 Schlagschrauber

Bedienungsanleitung

Makita BTD125 Schlagschrauber

Bedienungsanleitung

Makita TW011G Schlagschrauber

Verwandte Kategorien