Bedienungsanleitung Kity MTC355 Trennsäge

Bedienungsanleitung

tool, any part that appears damaged should

be carefully checked to determine that it will

operate properly and perform its intended

function.

• Check for alignment and binding of all

moving parts, broken parts or mounting

xtures and any other condition that may

affect proper operation. Any part that is

damaged should be properly repaired or

replaced by a qualied technician.

• Do not use the tool if any switch does not

turn off and on properly.

• Never force the tool or attachment to do the

work of a larger industrial tool. It is designed

to do the job better and more at the rate for

which it was intended.

• Always unplug the cord by the plug. Never

yank the cord out of the wall.

• Always turn off the machine before

unplugging.

• With normal use, the motor housing may get

hot.

• Make all adjustments to the machine with the

power OFF.

• Never leave the cutting off wheel saw

unattended while it is running.

• When turning off the machine, never leave

the cutting off wheel saw until it has come to

a complete stop.

• Make every effort to prevent snagging

by exercising special care when working

corners, sharp edges, ragged welds, etc.

• Do not use a cutting off wheel that is not in

accordance with specied sizes.

• Never carry the tool by the cord.

• Don’t pour water or coolant on cutting off

wheel when cutting.

• Make sure to secure cutting material so it

does not move during operation.

• Cutting material can get extremely hot during

operation.

If there is any question about a condition

about a condition being safe or unsafe, do

not operate the tool.

Operating instructions

■ CUTTING PROCESS, FIG. 2

Insert the work-piece and fasten it with clam-

ping handle 5 (g. 2).

Pay attention that the cut-off wheel does not

touch the work-piece when turning the machi-

ne on.

Switch the machine on; wait until the cut-

off wheel has reached full speed. Move the

machine head carefully downwards to the

work-piece.

Ensure you have constant pressure while

performing cut-off grinding work.

After the cutting switch the machine off and

move the machine head up.

Caution! The work-piece can get extremely

hot!

■ DIAGONAL CUTS: FIG. 3

For diagonal cuts, loosen both hexagon bolts

A of the rear clamping jaw, adjust the angle,

and tighten both screws again.

The clamping claw B automatically adjusts

to the angle. To do this, please use the ring

spanner (17mm).

■ QUICK CLAMPING LEVER: FIG. 4

The machine is equipped with a quick

clamping lever 8.

Move the lever 8 up, push the clamping

handle 5 forward to the work-piece, push

lever 8 down, afterwards lock the work-piece

using the clamping handle 5.

Attention! Prior to the cutting process, always

check that the work-piece is correctly and

securely tightened.

Long work-pieces must be supported by a

dolly (rolling support) or similar.

After work completion, place the machine

head in the lower position and pull out the

mains plug.

■ CUT-OFF WHEELS – REPLACEMENT FIG. 5 - 6

Attention! Pull out the mains plug.

Move machine head up, unfasten buttery nut

C, move the cover plate B and exible guard

10 up until the clamping screw of the cut-off

wheel is freely accessible. Press locking bolt

9 (g.6)

Move cut-off wheel by hand until the locking

bolt locks in place. Unscrew the clamping

screw by turning it counter-clockwise, using

the enclosed allen key. Remove the clamping

ange and the screw, mount the new wheel

and clamping ange, pay attention to correct

and neat position of the cut-off wheel, tighten

the screw slightly by hand, press the locking

bolt and fasten with the cut-off wheel spanner.

Mount the protective equipment and secure it

with buttery wing.

Check the functioning of the protective

equipment.

Attention! Cut-off wheel bore diameter must

match the ange diameter.

■ TRANSPORT: FIG. 7

Caution! Unplug

Press to move the machine the machine head

down and lock it with the locking bolt (12).

The saw is then locked in the bottom position.

■ OVERLOAD PROTECTION FIG. 7

The engine of this equipment is protected by a

circuit breaker (3) against overload.

When the rated current is exceeded, the

overload switch (3) on the device. After a short

cooling interval, the device can be switched on

again by pressing the overload switch (3).

Electrical connection m

The electrical motor installed is connected

and ready for operation. The connection

complies with the applicable VDE and DIN

provisions.

The customer‘s mains connection as well

as the extension cable used must also

comply with these regulations.

• The product meets the requirements of

GB

14

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr Kity MTC355 Trennsäge zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, Kity zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres Kity MTC355 Trennsäge in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für Kity Trennsägen
Weitere Anleitungen von Trennsägen

Häufig gestellte Fragen zu Kity MTC355 Trennsäge

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

Bosch GCO 20-14 Trennsäge

Bedienungsanleitung

Scheppach MT355s Trennsäge

Bedienungsanleitung

Parkside IAN 373210 Trennsäge

Bedienungsanleitung

Vonroc CS505AC Trennsäge

Bedienungsanleitung

Redstone MT100 Trennsäge

Bedienungsanleitung

Einhell TC-MC 355/1 Trennsäge

Bedienungsanleitung

Parkside IAN 327368 Trennsäge

Bedienungsanleitung

Parkside IAN 345868 Trennsäge

Verwandte Kategorien