Bedienungsanleitung FERM CDM1005 Bohrschrauber

Bedienungsanleitung

3. Protect the charger, battery block and power tool

from moisture, e.g. rain or snow.

4. Always check that all cables are connected correctly

before using the charger.

5. If you discover that a cable is damaged, you should

not use the charger again. Have the damaged cable

replaced immediately.

6. When the charger is not in use, the mains plug should

be removed from the power socket. Do not pull out

the plug by grasping the cable.

7. If the charger has been dropped or has otherwise

been exposed to high mechanical stresses, you

should have it checked for damage by an authorised

dealer before using it again. Damaged parts should be

repaired.

8. Exercise caution when handling the battery block

and do not drop it or expose it to impacts.

9. Never attempt to repair the charger or battery block

yourself. Repairs must always be carried out by an

authorised dealer - otherwise you risk an accident.

10. Before cleaning or servicing the charger or battery

block, always pull the plug from the charger socket.

11. Never charge the battery block when the ambient

temperature is below 5°C or above 40°C.

12. The air vents in the charger must never be blocked.

13. The battery block must not be short-circuited.

A short-circuit will cause a high current to flow. This

may result in overheating, the danger of fire or

explosion of the battery block. This may damage the battery

block or the user may risk an accident.

Therefore:

1. Do not connect any cables to the poles of the battery

block.

2. Take care that there are no metal objects (nails,

paper clips, coins, etc.) on the contact surface of the

battery block.

3. Do not expose the battery block to water or rain.

4, Only use the battery block supplied in combination

with this cordless drill/screwdriver so as to avoid faults

and/or risks to persons.

14. A damaged battery block or one that can no longer

be charged must be disposed of as special waste. Do

not discard it with household waste.

15. Never throw the battery block onto a fire or into

water. This will risk explosion!

ELECTRICAL SAFETY

Always check whether your battery voltage

matches that shown on the rating plate. Also find

out whether your mains voltage matches the input voltage of

the charger.

The battery charger is doubly insulated in

compliance with EN60335; it therefore does not

require earthing.

REPLACING CABLES OR PLUGS

Dispose of old cables or plugs immediately they are

replaced by new ones. Connecting a plug on a loose

cable to a socket is dangerous.

3. MOUNTING ACCESSORIES

Fig. B

Always remove the battery before starting work.

FITTING AND REMOVING DRILLS

In addition to drills, the tool can also accommodate

screwdriver bits with a hexagonal shaft.

• Loosen the drill chuck (4) by rotating the hand-grip

(9).

• Insert the shaft of the drill into the chuck.

• Tighten the drill chuck so that the drill is firmly

clamped.

• Rotate the drill chuck in the opposite direction when

you wish to change the cutter.

CONNECTING AND REMOVING THE

BATTERY

Fig. C

Ensure that the exterior of the battery block or tool

is clean and dry before connecting the charger.

• Ensure that the direction reversing switch (6 Fig. A) is

in the central position in order to prevent the

appliance from being switched on unexpectedly.

• Insert the charger (5) into the base of the appliance,

as shown on the illustration. Push the battery until it

latches in.

• Press the locking buttons (10) on both sides before

removing the battery, and disengage the battery

from the base of the appliance.

4. OPERATION

Fig. D

Always follow the safety notes and the relevant

safety code.

Hold the appliance firmly and press the drill steadily onto

the workpiece. Do not overload the appliance. Only use

drills with no visible wear. Worn drills will have a bad

effect on the functioning of the appliance.

ADJUSTING THE SPEED

The appliance has two drill speeds.

• For slow drilling or for driving or removing screws,

set the speed selection switch (2) to '1'.

• For fast drilling set the speed selection switch to '2'.

NEVER SWITCH OVER WHEN THE

MOTOR IS RUNNING!!!

ADJUSTING THE TORQUE

Fig. E

The appliance has 16 different torque settings with

which to set the power for driving and removing screws.

• Set the torque adjustment ring (3) to the desired

position. The available torque settings are indicated

on the adjustment ring by the numbers 1 to 8 and by

4 Ferm Ferm 45

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr FERM CDM1005 Bohrschrauber zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, FERM zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres FERM CDM1005 Bohrschrauber in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für FERM Bohrschrauber
Weitere Anleitungen von Bohrschrauber

Häufig gestellte Fragen zu FERM CDM1005 Bohrschrauber

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

FERM CDM1037 Bohrschrauber

Bedienungsanleitung

FERM CDM1038 Bohrschrauber

Bedienungsanleitung

FERM PDM1050P Bohrschrauber

Bedienungsanleitung

FERM CDM1134 Bohrschrauber

Bedienungsanleitung

FERM CDM1013 Bohrschrauber

Bedienungsanleitung

FERM CDM1008 Bohrschrauber

Bedienungsanleitung

FERM CDM1119 Bohrschrauber

Bedienungsanleitung

FERM PDM1049P_K Bohrschrauber

Verwandte Kategorien