Bedienungsanleitung Crivit IAN 93749 Fahrradlampe

Bedienungsanleitung

Introduction

Congratulations on the purchase of your new device.

You have chosen a high-quality product. This manual is part of the product. It includes

important information on safety, installation and disposal. Before using the product, please read the operating

and safety instructions carefully. Use the product only as described and according to its intended use. Include

all documentation when passing the device on to third parties.

Intended use

This product is intended as lighting for bicycles. LED bicycle lamp set is approved as sole lighting for all bicycle

types. Light distribution must not be obstructed by any other bicycle components or pieces of baggage. The

product is intended for use outside. Any use other than specified here or modification of the product is not

permitted and may lead to injuries and damage to the product. The manufacturer does not accept any liability

for damage caused by improper use. The product is not intended for commercial use.

Scope of delivery

1 Front light, 1 Rear light, 1 Front light holder,

1 Rear light holder, 4 AA rechargeable batteries, 4 AAA batteries,

Charger, Manual, Rubber reducers

Teilebeschreibung

A Front light B Rear light

C Front light holder D Rear light holder

E Power button- front light F Power button- rear light

G Battery indicator- front light H Battery indicator- rear light

I Battery charging socket J Angle adjustment screw - front light

K Retaining screw- Front light holder L Retaining screw- rear light holder

M Front light arrest N Rear light arrest

O Rear light rubber strap P Battery cover- front light

Q Battery compartment- front light R Battery cover- rear light

S Charger plug T Charger indicator

U Rubber reducers V Rear light battery tray

Technical data

Front light Rear light

Type designation: XC-112B / L-Lux 2.0 Type designation: XC-117K6 / Quattro L

Nominal power: 0.5 Watt Nominal power: 0.3 Watt

Protection class: IP44 acc. to DIN EN 60529 Protection class: IP44 acc. to DIN EN 60529

Rechargeable Batteries: 4 x 1.2 V AA HR6 Batteries: 4 x 1.5 V AAA LR03

Charger

Type designation: W&T-AD05W058060G

Input: 100-240 V ~ 0.2 A 50-60Hz Output: DC 5.8 V = 0.6 A

Note

Please only use rechargeable batteries with 1.2 V or comparable alkaline batteries with 1.5 V.

Safety note

WARNING!

RISK OF DEATH OR INJURY TO INFANTS AND CHILDREN!

Never leave children unattended with the packaging material as there is danger of suffocation by swallowing

packaging parts. Children often underestimate dangers. Always keep the product away from children. The

product is not a toy! This product is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities or lack of experience or knowledge, unless they are supervised by a person

responsible for their safety.

Please note that damage due to improper use, non-observance of the manual or intervention by non-authorised

persons is excluded from statutory warranty rights.

Do not disassemble the product. Improper repairs may lead to serious risks for the user. Repairs may only be

performed by authorised specialists. LEDs cannot be replaced.

Safety notes for batteries:

Keep batteries away from children, do not expose to fire or short-circuits or take them apart.

Observe polarity when inserting. Clean battery and device contacts before inserting if necessary.

Immediately remove empty batteries from the device! Increased risk of leakage!

Never expose batteries to excessive heat by sunlight, fire or similar.

Increased risk of leakage!

Non-compliance may lead to batteries being discharged beyond their final voltage and leaking! Remove

batteries immediately to avoid damage.

Avoid contact with skin, eyes and mucous membranes. If exposed to battery acid, wash the affected area

immediately with plenty of clear water and seek medical attention.

Always replace all batteries at the same time.

Only use batteries of the same type. Do not combine different types or used batteries with new batteries. Ensure

that the device is switched off after use. Remove batteries if the device is not used for long periods of time.

WARNING!

Do not recharge batteries! Risk of explosion!

NOTE!

If the red battery indicator on the front light G or rear light H is flashing, replace batteries or

recharge rechargeable batteries immediately.

Please observe that the lights no longer comply with the German road traffic registration regulation (StVZO) if

the battery indicator flashes.

Installation of front light

1 Screw out retaining screw K from holder C . 2 Position holder C at the desired location of the handle

bar. If necessary, use the rubber reducers U to ensure optimum fitting. 3 Screw in retaining screw K again.

Tighten the screw firmly. Do not use any tools in order to avoid damage. To set the optimum angle for the

direction of travel, unscrew the angle adjustment screw J with a cross-top screwdriver by 2-3 turns. Set the

desired angle and screw the angle adjustment screw J in tightly.

4 Slide the front light on the holder until it clicks in place. To release it, press the front light arrest M and slide

the front light to the front from the holder.

Front light charging option

The front light offers the option of connecting a charger to recharge rechargeable batteries inserted into the

front light.

To do so, remove the rubber cover from the battery charging socket I and connect the plug S of the charger

with the socket I . Afterwards, connect the charger with the power supply. The charger has a charging

indicator T . The batteries are empty if the indicator flashes red. If the indicator flashes green, the rechargeable

batteries can be used again and the front light is ready for use.

In order to preserve the full performance of the rechargeable batteries provided with the device, do not charge

the batteries for less than 10hrs when recharging them the first time. Do not interrupt the charging process

earlier, even if the charger LED is already flashing green. Subsequently, a charging time of approx. 6hrs is

recommended for rechargeable batteries with 1300 mAh.

Safety note, warning!

Risk of death and injury

Using the wrong charger may lead to damage, overheating or even explosion of the front light. In

this case, the warranty will expire.

WARNING!

Do not recharge batteries! Risk of explosion!

Cleaning

Clean the LED bicycle light set with a damp, lint-free cloth.

Note

Never emerge the light in water. Do not use corrosive or abrasive cleaning agents. This leads to

damage to the light.

Dispose of packaging and devices

in an environmentally friendly way!

Note on the disposal of batteries:

Low and empty batteries may be disposed of free of charge at official collection points, battery retailers or

recycling points.

Consumers are legally required to dispose of batteries at aforementioned battery collection points.

Below is the meaning of the symbols indicated on the batteries.

Do not dispose of batteries with household waste.

Batteries containing hazardous substances are additionally marked with the chemical symbol of the respective

substance:

- Pb: Lead - Hg: Mercury; - Cd: Cadmium

If batteries are not disposed of properly, valuable resources are lost and the hazardous substances contained

in the batteries may lead to risk for health and the environment. Separate collection/disposal of old batteries

helps to prevent risks for health and the environment. Valuable resources are regained by recycling.

Inserting rechargeable batteries/batteries into the front light

5 Slide back the cover P of the front light. 6 Remove the cover and take out the battery compartment Q of

the front light. 7 Insert rechargeable batteries on the top and bottom into the battery compartment. (4x AA,

1.2 V). Observe polarity when inserting the batteries. Afterwards, reassemble the light.

Installation of rear light

8 Attach the holder D with the rubber strip O to the seat post or the rear stay. Make sure that no objects are

covering the rear light. Tighten the rubber strip and hook it in. 9 Loosen the retaining screw L on the bracket

and adjust it until the desired angle is reached. Then, re-tighten the screw. Tighten the screw hand-tight. Do not

use any tools for this in order to avoid damage.

10

Slide the rear light onto the holder until it clicks in place.

To remove it, pull the rear light arrest N downwards and pull off the rear light.

Insert the battery into the rear light

11 Slide back the cover R of the rear light. 12 Remove the cover and remove the battery tray V from the

rear light. 13 Insert the batteries into the battery tray (4x AAA, 1.5 V) Observe the correct polarity. Then, put

the lamp back together.

Operation

The lamp has two brightness levels. Push the On/Off button E once to activate the Power mode

(20 lux) for cycling in unlit surroundings. Push the On/Off button E twice two activate the Eco mode

(10 lux) for cycling in lit surroundings. By pushing the On/Off button E again once (Eco mode) or

twice (Power mode), the lamp is switched off again. The rear lamp is switched on and off with the On/

Off switch F .

Safety note!

WARNING!

RISK OF DEATH AND INJURY!

Never recharge the batteries provided with the device. Risk of explosion!

Note on the disposal of device and packaging:

The packaging can be disposed of at local recycling points. For details, refer to your local authority.

Exclusively environmentally friendly materials have been used. If this product is to be disposed of,

do not throw it into household waste. Dispose of it appropriately according to your local guidelines. For further

information, refer to your local authority.

Declaration of conformity

KLB GmbH declares that this product with the following name conforms to applicable standards and EC

Directives.

EMC Directive 2004/108/EC and Directive 2011/65/EC (RoHS), LVM Directive 2006/95/EC. CB, GS, CE.

The following standards were taken as a basis:

DIN EN 55015:2009, DIN EN 61547:2010, DIN EN 6100-3-2:2010, DIN EN 61000-3-3:2009 and DIN EN

62321:2009, EN 61558-1:1997+A1+A11, EN 61558-2-6:1997, EN 60335-2-29 (latest version) DIN 33958.

Type designation: XC-112B / L-Lux 2.0; XC-117K6 / Quattro L; IAN 93749

Münster, G ermany 01.12.2013

Warranty provisions

Dear customers,

You will receive 3 years of warranty from the date of purchase. In case of faults to this product, you are entitled

to legal rights against the seller of this product. These legal rights are not limited by the warranty as described

below.

Warranty conditions

The warranty period begins with the date of purchase. Please keep your original receipt. It is required as

proof of purchase. If any material or manufacturing fault occurs regarding this product within three years

from date of purchase, the product will either be repaired or replaced by us free of charge, at our own

discretion. This warranty requires that the proof of purchase (receipt) as well as the faulty device be presented

to us within the period of three years with a short, written description of the fault and when it occurred. If the

fault is covered by our warranty, you will either receive a repaired or a new product back from us. With the

repair or replacement of the product, no new warranty period begins.

The warranty period is not extended by statutory warranty rights. This also includes replaced and repaired

components. Damage and faults at purchase must be reported immediately after unpacking the device.

Repairs after expiry of the warranty period are subject to charge.

Extent of warranty

The device was carefully manufactured under observation of strict quality requirements and thoroughly

tested before delivery. The warranty applies to material or manufacturing faults. It does not include product

components which are subject to normal wear, and therefore regarded as wear parts, or damage to fragile

components e. g. switches, rechargeable batteries or glass parts. This warranty expires if the product is not

maintained or used properly or when damaged. For proper use of the device, all instructions included in the

manual must be observed.

Applications or handling which is inappropriate according to the manual must be avoided. The product is only

intended for private use, not for commercial use. The warranty expires in case of inappropriate use, the use of

violence, and modifications not performed by one of our authorised service providers.

Please observe the following instructions to ensure proper processing of your request:

• Pleasehaveyourreceiptandthearticlenumberreadyasproofofpurchasewhenmakinganinquiry.

• Thearticlenumbercanbefoundonthenameplateoronthecoverofthismanual.

• Incaseofmalfunctionsorfaults,pleasecontacttheservicedepartmentbelowbyphoneoremailasarst

step.

• Products registered as faultfaulty can be r

eturned free of charge to the service address given to you

including proof of purchase (receipt) and information about the fault and when it has occurred. Please note

that the service department must be informed before sending the device.

Manuals, including this one, product videos, and software can be found at www.lidl-service.com.

SERVICE + SUPPLIER SERVICE + SUPPLIER

KLB GmbH KLB GmbH

Diekbree 8 Diekbree 8

48157 Münster, Germany 48157 Münster, Germany

Tel: +49 2 51 132 37 57 Tel: +49 2 51 132 37 57

E-Mail: gb@klb-service.eu E-Mail: ie@klb-service.eu

www.klb-service.eu www.klb-service.eu

IAN 93749 IAN 93749

Information date: 12/2013

Version: 14101/14102 - DE

LED bicycle light set

with charger

IAN 93749 / Article 14101

IAN 93749 / Article 14102

I A N 93749

Front light Rear light

4

5

6

7

7

8

11

9

12

10

13

1

2

3

HR6 1,2V

LR03 1,5V

LR03 1,5V

HR6 1,2V

close open

4x AA

4x AAA

4x AAA

4x AA

GB IE

GB IE

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr Crivit IAN 93749 Fahrradlampe zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, Crivit zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres Crivit IAN 93749 Fahrradlampe in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für Crivit Fahrradlampen
Weitere Anleitungen von Fahrradlampen

Häufig gestellte Fragen zu Crivit IAN 93749 Fahrradlampe

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

Crivit IAN 307557 Fahrradlampe

Bedienungsanleitung

Crivit IAN 298456 Fahrradlampe

Bedienungsanleitung

Crivit IAN 300377 Fahrradlampe

Bedienungsanleitung

Crivit IAN 285919 Fahrradlampe

Bedienungsanleitung

Crivit IAN 96683 Fahrradlampe

Bedienungsanleitung

Crivit IAN 22378 Fahrradlampe

Bedienungsanleitung

Crivit IAN 292866 Fahrradlampe

Bedienungsanleitung

Crivit IAN 278515 Fahrradlampe

Verwandte Kategorien