Bedienungsanleitung Stickfast GX600A Klebepistole

Bedienungsanleitung

W

hen you have finished using the gun:

1. Switch o and disconnect the gun from the power supply.

2. Do not remove the unused glue stick from the gun as this

may damage the feed mechanism and will invalidate the

warranty. The adhesive can be stored indefinitely in the

u

nheated gun and re-melted by reheating the gun the next

t

ime it is required.

3. Ensure the stand (if supplied separately) is securely

attached to the gun as per the instructions.

4

. Place the gun in an upright position on a flat, stable surface.

5

. Ensure the hot nozzle cannot cause damage to

surrounding areas.

6. Ensure the gun is completely cool before placing it in

confined spaces

7. Do not wrap the power cable around the gun unless the

g

un is completely cool.

Adhesive may occasionally drip from the heated gun; this is

normal and due to expansion of the adhesive. The Stickfast™

HGS11 Heat Resistant Mat protects the work area and glue

droplets are easily removed when set.

Some materials are heat sensitive and can be damaged by hot

glue. Wherever possible test a piece of scrap material or a

hidden portion of the object before commencing production.

Tips on use

The following information may be helpful concerning the use

of Stickfast™ glue guns and hot melt adhesives.

1. Parts to be bonded should be pressed together within 15-20

seconds of application, as normal working time for hot melts

is between 15 and 35 seconds, and 90% maximum bond

strength is reached in 2 minutes.

2. Working time can be extended and reduced by adjusting the

size of the glue deposits (larger deposits cool slower).

3. Large areas may not perfectly bond if the adhesive sets

before the full area is covered. For possible solutions to this

problem contact your distributor.

4. Preheating of surfaces to be bonded to slightly above room

temperature will improve the bond strength. This is

particularly important when gluing metal components.

5. Hot melts begin melting at 70-80°C and are not suitable for

use where high temperatures will occur after assembly.

6. Hot melt adhesives can be used as a replacement for nails,

staples, tape or liquid glue but should not be used to replace

structural fasteners where heavy loads are involved.

7. If your glue is ‘stringing’ from the nozzle, swirl the nozzle in a

circular motion to cut the string using the external surface

heat of the nozzle.

Xtegra

®

Stickfast™ Accessories

Replacement nozzles

HGS00 Short Nozzle

HGS01 Medium Nozzle

HGS02 Extended Nozzle

HGS03 Nozzle Adaptor Piece

HGS04 5-hole Spreader Nozzle (requires HGS03)

HGS05 Extended Slimline Nozzle

HGS06 19-hole Spreader Nozzle

HGS07 Angled Nozzle

HGS11 Heat Resistant Mat

Tool balances (for suspending glue gun over work area)

HGS12 Tool Balance, 0-1.5kg

HGS13 Tool Balance, 1.5 - 3.0kg

EDITION FEB 2017

Preventative maintenance

1. Use only genuine Xtegra

®

Stickfast™ glue sticks. Other

m

anufacturers’ sticks vary in size which may compromise

gun performance and will invalidate the Xtegra

®

warranty.

2. To prevent the clogging of the glue gun, keep the feed

mechanism and melt chamber free from dirt and other

f

oreign debris. Store unused glue sticks in their original

p

ackaging and in a clean environment.

3

. Do not remove the glue stick from the back of the gun, as this

will damage or impair the feed mechanism.

4. To change to another glue type, cut o any protruding glue

stick and by inserting a stick of the new glue, flush the

p

revious glue from the gun.

5. Do not place the heated gun on its side for long periods; use

the support stand provided to keep it upright.

6. If melted glue escapes from the melt chamber at the rear of

the gun and interferes with the feed mechanism, allow the

gun to cool then gently remove the obstructing glue.

7

. In the event of excessive glue leakage from the nozzle, re

place the nozzle.

a) Do not attempt to change the nozzle while the gun is cold.

b) Heat the gun until the glue has softened enough to re

move the nozzle (about one minute).

c) Wearing heat resistant gloves, use a spanner to remove

the old nozzle.

d) Flush glue through the gun to clear the melt chamber.

e) Replace with new nozzle and tighten to a snug fit. Do not

over-tighten.

Service and repairs

Xtegra

®

Stickfast™ glue guns must be returned to the supplier

for servicing or repairs at the user’s cost. Providing Stickfast™

glue sticks have been used at all times, parts replaced due to

faulty workmanship or materials under normal conditions of

use and in strict accordance with the operating instructions

will be replaced within 12 months from the date of purchase.

Within this period the supplier retains the right to decide

whether to have the gun repaired or replaced. All repairs and

servicing will be fully chargeable if glue sticks other than

Stickfast™ have been used.

The supplier reserves the right to improve or modify this

product without prior notice.

IMPORTANT!

To ensure the best performance from your applicator follow

the tips below:

> ALWAYS allow the applicator to warm up to operating

temperature before use. Most guns are ready for use within

5-7 minutes.

> NEVER lay the glue gun on its side. Always use the gun stand

supplied or another suitable gun stand or suspension hook.

> ALWAYS UNPLUG the glue gun if it is not to be used for

periods in excess of 40 minutes!

> NEVER withdraw a partially melted glue stick through the

back of the gun, as this may damage the feed mechanism.

> NEVER remove the nozzle from a cold applicator as thread

can be damaged. Remove when warm, wearing heat-

resistant gloves.

> To aid EASIER STARTUP the next time the applicator is used,

disconnect from the power supply when work is complete

and feed about half a stick of molten glue through the gun

during the cooling process.

5

STICKFAST Operating Instructions

G

B

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr Stickfast GX600A Klebepistole zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, Stickfast zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres Stickfast GX600A Klebepistole in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für Stickfast Klebepistolen
Weitere Anleitungen von Klebepistolen

Häufig gestellte Fragen zu Stickfast GX600A Klebepistole

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

Stickfast SL150B Klebepistole

Bedienungsanleitung

Stickfast GX80 Klebepistole

Bedienungsanleitung

Stickfast GX300 Klebepistole

Bedienungsanleitung

Stickfast GX120 Klebepistole

Bedienungsanleitung

Stickfast SL120 Klebepistole

Bedienungsanleitung

Stickfast GX80LT Klebepistole

Bedienungsanleitung

Stickfast GX600 Klebepistole

Bedienungsanleitung

Stickfast SL300 Klebepistole

Verwandte Kategorien