Bedienungsanleitung Sparky BM 1060E Handrührwerk

Bedienungsanleitung

7

Original instructions

EN

results in smooth increase of the rpm to maxi-

mum upon reaching the extreme position.

ELECTRONIC SPEED PRE-SELECTION

The necessary speed can be pre-selected by

rotating the regulator dial 3 to the direction of

the arrow or to the mark “+” for increasing, and

to the direction opposite to the arrow or towards

the mark “-” for decreasing the speed, thus en-

suring optimum mode.

The mixer BM2 1060CEplus is equipped with

two-speed gear. Switching between the speeds

is performed by rotating the speed selector

switch 9 to 180º in the direction of the arrow,

marked on the switch, with the machine stopped

(anti-clockwise).

INSERTING OR REPLACING THE MIX-

ING PADDLE

Unplug the machine in case the plug has been

inserted in the socket.

Screw the mixing paddle 6 by hand in clockwise

direction.

Using the open end spanner SW22 unscrew

harshly the mixing paddle 6 in anti-clockwise di-

rection. In case the mixing paddle has jammed,

use an auxiliary 19 mm spanner applied at the

wrench at 13 to x the spindle 7.

RECOMMENDATIONS

The mixing paddle is still rotating for a while af-

ter the machines has been switched off.

If the rotating paddle touches a surface, a re-

bound may result.

Start the machine by slowly pressing the switch

trigger 2 to reach maximum speed only after the

mixing paddle has already been dipped into the

mixture.

OVERLOAD PROTECTION (ONLY

FOR MODELS BM 1060CEPLUS AND

BM2 1060CEPLUS)

Upon minor long overloads, the thermal over-

load protection actuates and switches the motor

off. To resume operation after cooling down for

approximately 3-5 min, switch the trigger off and

on again.

Current protection actuates upon large brief

overloads. It interrupts the supply and disables

the machine. To start operating the machine,

rst switch off and then switch on the lever of

ON/OFF switch.

ACCESSORIES TO BE USED WITH

THIS POWER TOOL

- Mixing paddles with right wise rotation, M14

outer thread and Ømax140 can be used with

this power tool.

- Mixing paddle SM120x570

- Mixing paddle SM121x570

The delivery does not necessarily include the

mixing paddles SM120x570 and SM121x570.

Maintenance

WARNING: Always ensure that the

tool is switched off and unplugged before

attempting to perform inspection or mainte-

nance.

BRUSH REPLACEMENT

This power tool is equipped with auto-stop

brushes. When the carbon brushes are worn

out, the machine switches itself off. In this case

both brushes must be replaced simultaneously

with genuine brushes at SPARKY service centre

for warranty and post-warranty service.

GENERAL INSPECTION

Regularly inspect all fasteners and ensure they

are properly tightened. Should any of the screws

be loose, retighten it immediately to avoid haz-

ards.

If the replacement of the supply cord is neces-

sary, this has to be done by the manufacturer or

his agent in order to avoid a safety hazard.

CLEANING

For safe operation always keep the machine

and its ventilation slots clean.

Regularly check to see if any dust or foreign

matter has entered the ventilation slots and the

grills around the switches. Use a soft brush and/

or air jet to remove any accumulated dust. Wear

safety glasses to protect your eyes whilst clean-

ing.

Exterior plastic parts may be cleaned with a

damp cloth and mild detergent if necessary.

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr Sparky BM 1060E Handrührwerk zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, Sparky zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres Sparky BM 1060E Handrührwerk in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für Sparky Handrührwerke
Weitere Anleitungen von Handrührwerke

Häufig gestellte Fragen zu Sparky BM 1060E Handrührwerk

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

Sparky BM 1060CE Plus Handrührwerk

Bedienungsanleitung

Sparky BM 1380CE Plus Handrührwerk

Bedienungsanleitung

Sparky BM 1360CE Plus Handrührwerk

Bedienungsanleitung

Sparky BM2 1360CE Plus Handrührwerk

Bedienungsanleitung

Sparky BM2 1380CE Plus Handrührwerk

Bedienungsanleitung

Sparky BM2 1060CE Plus Handrührwerk

Bedienungsanleitung

Collomix XQ6 Handrührwerk

Bedienungsanleitung

Unimix U 900 Handrührwerk

Verwandte Kategorien