Bedienungsanleitung Skil 3810 CA Bohrhammer

Bedienungsanleitung

11

- it takes a short time for the hammer mechanism to

reach full impact power

- best hammer drilling results can be obtained by only a

slight pressure on the tool; drilling performance will not

improve by applying more pressure on the tool

• Battery protection

Switches o the tool or prevents the tool from being

switched on, when

- the load is too high

- the battery temperature is not within the allowable

operating temperature range of -20 to +50°C

- the lithium-ion battery is nearly empty (to protect

against deep discharge)

! 



damaged

• LED-light E

r

- LED-light E automatically lights on when activating

switch A

2

• Holding and guiding the tool

t

! while working, always hold the tool at the grey-

coloured grip area(s)

- keep ventilation slots F

2

uncovered

- do not apply too much pressure on the tool; let the tool

do the work for you

APPLICATION ADVICE

• Use the appropriate bits

y

! only use sharp bits

• For drilling with non SDS drill bits in wood, metal and

plastic, use an adapter (not standard included)

u

! clean and lightly lubricate the SDS+ accessory

before insertion

- pull back locking sleeve C

2

and insert adapter

in SDS+ chuck while turning and pushing it until it

engages; the adapter locks in position automatically

- pull adapter to check whether is it locked correctly

- set switch D

2

to normal drilling (only activate when

tool is switched o and the switch is locked)

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking

of the wood

• Splinterfree drilling in wood

i

• Dustfree drilling in walls

o

• Dustfree drilling in ceilings

p

• Drilling in tiles without skidding

a

• For more information see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool clean (especially ventilation slots F

2

)

! remove battery from tool before cleaning

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should

be carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of the

tool are listed on www.skil.com)

• Only use the following batteries and chargers with

this tool

- SKIL battery: BR1*31****

- SKIL charger: CR1*31****

• Do not use the battery when damaged; it should be

replaced

• Do not disassemble the battery

• Do not expose tool/battery to rain

• Permitted ambient temperature (tool/charger/battery):

- when charging 4...40°C

- during operation –20...+50°C

- during storage –20...+50°C

EXPLANATION OF SYMBOLS ON TOOL/BATTERY

3

Read the instruction manual before use

4

Batteries may explode when disposed of in re, so do not

burn battery for any reason

5

Store tool/charger/battery in locations where temperature

will not exceed 50°C

6

Do not dispose of electric tools and batteries together

with household waste material

USE

• Combined switch for on/o and speed control A

2

8

9

- control the speed steplessly from zero to maximum by

putting less or more pressure on the trigger

• Charging battery

! read the safety warnings and instructions

provided with the charger

• Removing/installing the battery

2

• Battery level indicator

7

- press the battery level indicator button H to show the

current battery level.

• Changing direction of rotation

q

- when not properly set in left/right position, switch A

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Changing bits

w

! clean and lightly lubricate the SDS+ accessory

before insertion

- pull back locking sleeve C and insert accessory

in SDS+ chuck while turning and pushing it until it

engages; the accessory locks in position automatically

- pull accessory to check that it is locked correctly

- remove accessory by pulling back locking sleeve C

! the SDS+ accessory requires freedom of

movement which causes eccentricity when tool





drilling precision

! when using hex bits, make sure that these hex bits

are at least 75 mm long, or otherwise use shorter

hex bits with hex adapter G

! do not use bits with a damaged shank

• Selecting operating mode

e

1 = normal drilling/screwdriving

2 = hammer drilling

! select operating mode only when tool is switched



- the hammer mechanism is activated by applying a

slight pressure on the tool when the drill bit is in contact

with the workpiece

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr Skil 3810 CA Bohrhammer zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, Skil zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres Skil 3810 CA Bohrhammer in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für Skil Bohrhämmer
Weitere Anleitungen von Bohrhämmer

Häufig gestellte Fragen zu Skil 3810 CA Bohrhammer

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

Skil 1035 AK Bohrhammer

Bedienungsanleitung

Skil 1781 GB Bohrhammer

Bedienungsanleitung

Skil 3851 CA Bohrhammer

Bedienungsanleitung

Skil 3810 GA Bohrhammer

Bedienungsanleitung

Skil 3851 JA Bohrhammer

Bedienungsanleitung

Skil 3810 FA Bohrhammer

Bedienungsanleitung

Skil 1781 GA Bohrhammer

Bedienungsanleitung

Skil 1762 AK Bohrhammer

Verwandte Kategorien