Bedienungsanleitung Skil 1525 A1 Hobel

Bedienungsanleitung

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions and in the

manner intended for the particular type of power

tool, taking into account the working conditions and

the work to be performed. Use of the power tool for

operations different from those intended could result in a

hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is

maintained.

SAFETY INSTRUCTIONS FOR PLANERS

● Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

● Always keep the cord away from moving parts of the

tool; direct the cord to the rear away from the tool

● Wait for the cutter block to stop before setting the

tool down (an exposed knife may engage the surface

leading to possible loss of control and serious injury)

● Use completely unrolled and safe extension cords with a

capacity of 16 Amps (UK 13 Amps)

● In case of electrical or mechanical malfunction,

immediately switch off the tool and disconnect the plug

● SKIL can assure flawless functioning of the tool only

when original accessories are used

● This tool should not be used by people under the age of

16 years

● The noise level when working can exceed 85 dB(A);

wear ear protection

● Do not work materials containing asbestos (asbestos

is considered carcinogenic)

● Take protective measures when during work dust

can develop that is harmful to one's health,

combustible or explosive (some dusts are considered

carcinogenic); wear a dust mask and work with dust/chip

extraction when connectable

● If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

● Never use tool when cord is damaged; have it replaced

by a qualified person

● Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

● If any chip should get jammed in the chip outlet, you

should switch off the motor, ensure that all moving parts

have come to a complete standstill, disconnect the plug,

and remove the jammed chip

● Before using the tool check that the knives do not brush

anywhere

● Keep your fingers away from the rotating knives

● Only use high speed steel (HSS) or carbide-tipped (TC)

knife sets with this tool

● Always disconnect plug from power source before

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

● Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

● If for any reason the old plug is cut off the cord of this

tool, it must be disposed of safely and not left

unattended

USE

● Changing/reversing knives 3

This planer is equipped with non-grindable knives with

cutting edges on both sides; so if one side has become

blunt, the other side can be used

! switch off the tool and disconnect the plug

- remove guiding devices, if mounted

- take wrench from storage A 2

- turn planer upside down

- loosen 3 bolts B with wrench C (do not remove bolts)

- remove clamping element D from cutter block E while

pushing safety bracket F downwards

- push knife out of clamping element with piece of

wood (for easy removal clean knife first with

petroleum or spirit)

- for mounting a new or reversed knife handle vice-

versa (clean knife and clamping element first)

! ensure that the clamping element rests on side

stop of cutter block

! groove in knife should match ledge in cutter block

! ensure that knife end near safety bracket aligns

with edge of foot (set a ruler flat against housing as

illustrated and use it as a stopper)

- firmly tighten 3 bolts B with wrench C

! change/reverse knives in time; only use sharp

knives

! always change/reverse both knives at the same

time

! do not attempt to adjust the knives with cutter

block screws G, which are pre-set at

manufacturing

● Adjusting planing depth

- turn knob H 2 to select required depth by using scale

J 2

- maximum planing depth 2.5 mm

- always select a shallow planing depth and repeat the

planing and adjusting process until the required depth

is reached

● Dust suction

- when planing one may use a dust bag (SKIL

accessory 2610387871)

! do not attempt to remove any obstructions from

the dust port K 3 while knives are rotating

6

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr Skil 1525 A1 Hobel zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, Skil zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres Skil 1525 A1 Hobel in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für Skil Hobel
Weitere Anleitungen von Hobel

Häufig gestellte Fragen zu Skil 1525 A1 Hobel

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

Skil 1590 DA Hobel

Bedienungsanleitung

Skil 1558 AA Hobel

Bedienungsanleitung

Skil 1565 AD Hobel

Bedienungsanleitung

Skil 1590 AA Hobel

Bedienungsanleitung

Pattfield PPL900B Hobel

Bedienungsanleitung

Ryobi EPN7582N Hobel

Bedienungsanleitung

Bosch GHO 12V-20 Hobel

Bedienungsanleitung

Bosch GHO 6500 Hobel

Verwandte Kategorien