Bedienungsanleitung Ryobi R18MS216-0 Gehrungssäge

Bedienungsanleitung

■ Cut only one workpiece at a time. Stacked multiple

workpieces cannot be adequately clamped or braced

and may bind on the blade or shift during cutting.

■ Ensure the mitre saw is mounted or placed on a

level, firm work surface before use. A level and

firm work surface reduces the risk of the mitre saw

becoming unstable.

■ Plan your work. Every time you change the bevel or

mitre angle setting, make sure the adjustable fence

is set correctly to support the workpiece and will

not interfere with the blade or the guarding system.

Without turning the tool “ON” and with no workpiece

on the table, move the saw blade through a complete

simulated cut to assure there will be no interference or

danger of cutting the fence.

■ Provide adequate support such as table extensions,

saw horses, etc. for a workpiece that is wider or

longer than the table top. Workpieces longer or

wider than the mitre saw table can tip if not securely

supported. If the cut-off piece or workpiece tips, it can

lift the lower guard or be thrown by the spinning blade.

■ Do not use another person as a substitute for a

table extension or as additional support. Unstable

support for the workpiece can cause the blade to bind

or the workpiece to shift during the cutting operation

pulling you and the helper into the spinning blade.

■ The cut-off piece must not be jammed or pressed

by any means against the spinning saw blade. If

confined, i.e. using length stops, the cut-off piece could

get wedged against the blade and thrown violently.

■ Always use a clamp or a fixture designed to

properly support round material such as rods or

tubing. Rods have a tendency to roll while being cut,

causing the blade to “bite” and pull the work with your

hand into the blade.

■ Let the blade reach full speed before contacting the

workpiece. This will reduce the risk of the workpiece

being thrown.

■ If the workpiece or blade becomes jammed, turn the

mitre saw off. Wait for all moving parts to stop and

disconnect the plug from the power source and/

or remove the battery pack. Then work to free the

jammed material. Continued sawing with a jammed

workpiece could cause loss of control or damage to the

mitre saw.

■ After finishing the cut, release the switch, hold the

saw head down and wait for the blade to stop before

removing the cut-off piece. Reaching with your hand

near the coasting blade is dangerous.

SAFETY INSTRUCTIONS FOR WOOD CUTTING

BLADE

■ Please read the manual and instructions carefully

before using the saw blade and the machine.

■ The product must be in good condition, the spindle

without deformation and vibration.

■ Do not use the product without the guards in position.

Keep guards in good working order and properly

maintained.

■ Ensure the operator is adequately trained in safety

precautions, adjustment and operation of the product.

■ Always wear goggles and ear protection when using the

product. It is recommended to wear gloves, sturdy non

slipping shoes and apron.

■ Before using any accessory, consult the instruction

manual. The improper use of an accessory can cause

damage and increase the potential for injury.

■ Use only blades specified in this manual, complying

with EN 847-1.

■ Observe the maximum speed marked on the saw

blade. Ensure the speed marked on the saw blade is at

least equal to the speed marked on the saw.

■ Always use blades with correct size and shape of

arbour holes. Blades that do not match the mounting

hardware of the saw will run eccentrically, causing loss

of control.

■ Do not use blades of larger or smaller diameter than

recommended. Do not use any spacers to make the

blade fit onto the spindle.

■ Check the tips of the saw blade for damage or abnormal

appearance before each use. Tips that are damaged or

loose can become flying objects in use and increase the

chance of personal injury.

■ Do not use cracked or distorted saw blades. Do not use

saw blades that are damaged or deformed.

■ Scrap the saw blade if damaged, deformed, distorted or

cracked, repairing is not permitted.

■ Do not use HSS blades.

■ Ensure the saw blade is mounted correctly, tighten the

arbor nut securely before use (tightening torque approx.

12-15 Nm).

■ Fastening screw and nuts shall be tightened using the

appropriate spanner, etc.

■ Extension of the spanner or tightening using hammer

blows is not permitted.

■ Make sure the blade and flanges are clean and the

recessed sides of the collar are against the blade.

■ Make sure the blade rotates in the correct direction.

■ Before work, make a dummy cut without the motor

turned on so the position of the blade, operation of

the guards with respect to other machine parts and

workpiece may be checked.

■ Never leave the product unattended.

■ Do not apply lubricants on the blade when it is running.

■ Never perform any cleaning or maintenance work when

the machine is still running and the head is not in the

rest position.

■ Never attempt to stop a machine in motion rapidly

by jamming a tool or other means against the blade,

serious accidents can be caused unintentionally in this

way.

■ Disconnect the product from the mains supply or

remove battery pack before changing blades or carrying

out maintenance.

■ Pay attention to blade packing and unpacking, it is easy

to be injured by the sharp blade tips.

■ Use a blade holder or wear gloves when handling a saw

blade.

■ Keep and store the blade in original packaging or other

suitable packaging, keep in dry conditions and away

from chemicals which may damage the blade.

ENGLISH

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

BG

UK

TR

EL

3

Original Instructions

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr Ryobi R18MS216-0 Gehrungssäge zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, Ryobi zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres Ryobi R18MS216-0 Gehrungssäge in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für Ryobi Gehrungssägen
Weitere Anleitungen von Gehrungssägen

Häufig gestellte Fragen zu Ryobi R18MS216-0 Gehrungssäge

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

Ryobi EMS190DC Gehrungssäge

Bedienungsanleitung

Ryobi RMS18254X-0 Gehrungssäge

Bedienungsanleitung

Ryobi RMS18190-0 Gehrungssäge

Bedienungsanleitung

Ryobi ETMS1825 Gehrungssäge

Bedienungsanleitung

Vonroc MS506AC Gehrungssäge

Bedienungsanleitung

FEMI 305 PRO Gehrungssäge

Bedienungsanleitung

Einhell TE-SM 8 L Dual Gehrungssäge

Bedienungsanleitung

Stayer SC 291 W Gehrungssäge

Verwandte Kategorien