Bedienungsanleitung Rotel RMB-1575 Verstärker

Bedienungsanleitung

9

English

If you are using terminal lugs, connect them to the wires. If you are

attaching bare wires directly to the speaker connectors, separate the

wire conductors and strip back the insulation from the end of each

conductor. Be careful not to cut into the wire strands. Unscrew (turn

counterclockwise) the speaker connector collar. Place the connector lug

around the shaft, or insert the bundled wire into the hole in the shaft.

Turn the collars clockwise to clamp the connector lug or wire fi rmly in

place.

NOTE: Be sure there are no loose wire strands that could touch

adjacent wires or connectors.

Troubleshooting

Most diffi culties in audio systems are the result of poor or wrong

connections, or improper control settings. If you encounter problems,

isolate the area of the diffi culty, check the control settings, determine

the cause of the fault and make the necessary changes. If you are

unable to get sound from the amplifi er, refer to the suggestions for the

following conditions:

Front Panel Power Indicator Is Not Lit

No mains power to the amplifi er. Check AC power connections at

the amplifi er and the AC outlet. Check the front panel power switch.

Make sure that it is set to the ON position. If using 12V trigger power-

on, make sure that a trigger signal is present at rear panel screw

terminals.

No Sound

If the amp is getting AC power, but is producing no sound, check

the PROTECTION INDICATOR on the front panel. If lit, see below. If

not, check all of your connections and control settings on associated

components. Make sure that your input connections and speaker

connections match your selected confi guration.

Protection Indicator Is Lit

The front panel PROTECTION INDICATOR is lit when the amplifi er

protection circuits have shut off the amplifi er. Typically, this occurs

only when the amplifi er has overheated, when there is faulty speaker

wiring, or after a period of extreme use. Turn off the system and wait

for the amp to cool. Then push the front panel power switch in and

out to reset the protection devices. If the problem is not corrected or

reoccurs, there is a problem with the system or the amplifi er itself.

Specifi cations

RMB-1565

Continuous Power Output

Continuous Power Output 100 watts/channel

(20-20 kHz, < 0.03%, 8 ohms)

Total Harmonic Distortion

Total Harmonic Distortion (20Hz-20kHz, 8 ohms) < 0.03%

Intermodulation Distortion

Intermodulation Distortion (60 Hz : 7 kHz, 4:1) < 0.03%

Frequency Response

Frequency Response ( ±1dB) 10Hz - 40kHz

Damping Factor

Damping Factor (20-20,000 Hz, 8 ohms) 200

Speaker Impedance

Speaker Impedance (Normal mode) 4 ohms minimum

Signal to Noise Ratio

Signal to Noise Ratio (IHF A network) 105 dB

Input Impedance/Sensitivity

Input Impedance/Sensitivity 8.2 k Ohms/1.25 volt

Power Requirements

Power Requirements 110 -240 Volts, 50-60 Hz

Power Consumption

Power Consumption 250 Watts

Dimensions

Dimensions

Width x Height x Depth 431 x 99 x 339 mm

17 x 3

7

/8 x 13

3

/8 ins.

Front Panel Height 2U

Weight

Weight (net) 6 kg, 13.23 lb.

RMB-1575

Continuous Power Output

Continuous Power Output 250 watts/channel

(20-20 kHz, < 0.03%, 8 ohms)

Total Harmonic Distortion

Total Harmonic Distortion (20Hz-20kHz, 8 ohms) < 0.03%

Intermodulation Distortion

Intermodulation Distortion (60 Hz : 7 kHz, 4:1) < 0.03%

Frequency Response

Frequency Response ( ±1dB) 10Hz - 80kHz

Damping Factor

Damping Factor (20-20,000 Hz, 8 ohms) 400

Speaker Impedance

Speaker Impedance (Normal mode) 4 ohms minimum

Signal to Noise Ratio

Signal to Noise Ratio (IHF A network) 109 dB

Input Impedance/Sensitivity

Input Impedance/Sensitivity 8.3 k Ohms/1.5 volt

Power Requirements

Power Requirements

U.S. version 120 Volts, 60 Hz

European version 230 Volts, 50 Hz

Power Consumption

Power Consumption 600 Watts

Dimensions

Dimensions

Width x Height x Depth 431 x 144 x 406 mm

17 x 5

11

/16 x 16 ins.

Front Panel Height 3U

Weight

Weight (net) 11 kg, 24.25 lb.

All specifications are accurate at the time of printing.

Rotel reserves the right to make improvements without notice.

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr Rotel RMB-1575 Verstärker zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, Rotel zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres Rotel RMB-1575 Verstärker in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für Rotel Verstärker
Weitere Anleitungen von Verstärker

Häufig gestellte Fragen zu Rotel RMB-1575 Verstärker

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

Rotel RB-1080 Verstärker

Bedienungsanleitung

Rotel RC-06 Verstärker

Bedienungsanleitung

Rotel RB-1590 Verstärker

Bedienungsanleitung

Rotel RA-1312 Verstärker

Bedienungsanleitung

Rotel RMB-1506 Verstärker

Bedienungsanleitung

Rotel RMB-1077 Verstärker

Bedienungsanleitung

Rotel RB-1582MKII Verstärker

Bedienungsanleitung

Rotel A11 Verstärker

Verwandte Kategorien