Bedienungsanleitung Makita M6000 Bohrschrauber

Bedienungsanleitung

4

Reversing switch action (Fig. 2)

For Model M6001, M6002

This tool has a reversing switch to change the direction

of rotation. Move the reversing switch lever to the

D

position (A side) for clockwise rotation or to the E

position (B side) for counterclockwise rotation.

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing drill bit

CAUTION:

• Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

For Model M6000, M6001 (Fig. 3)

To install the bit, place it in the chuck as far as it will go.

Tighten the chuck by hand. Place the chuck key in each

of the three holes and tighten clockwise. Be sure to

tighten all three chuck holes evenly.

To remove the bit, turn the chuck key counterclockwise in

just one hole, then loosen the chuck by hand.

For Model M6002 (Fig. 4)

Hold the ring and turn the sleeve counterclockwise to

open the chuck jaws. Place the bit in the chuck as far as

it will go. Hold the ring firmly and turn the sleeve

clockwise to tighten the chuck.

To remove the bit, hold the ring and turn the sleeve

counterclockwise.

OPERATION (Fig. 5)

Holding the tool

Always hold the tool only by the handle when performing

an operation. Do not touch the metal part.

Drilling operation

Drilling in wood

When drilling in wood, the best results are obtained with

wood drills equipped with a guide screw. The guide

screw makes drilling easier by pulling the bit into the

workpiece.

Drilling in metal

To prevent the bit from slipping when starting a hole,

make an indentation with a center-punch and hammer at

the point to be drilled. Place the point of the bit in the

indentation and start drilling.

Use a cutting lubricant when drilling metals. The

exceptions are iron and brass which should be drilled dry.

CAUTION:

• Pressing excessively on the tool will not speed up the

drilling. In fact, this excessive pressure will only serve

to damage the tip of your bit, decrease the tool

performance and shorten the service life of the tool.

• There is a tremendous force exerted on the tool/bit at

the time of hole break through. Hold the tool firmly and

exert care when the bit begins to break through the

workpiece.

• Always secure small workpieces in a vise or similar

hold-down device.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

ENG905-1

Noise

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

pA

): 77 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection

ENG900-1

Vibration

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Work mode: drilling into metal

Vibration emission (

a

h, D

): 3.0 m/s

2

Uncertainty (K): 1.5 m/s

2

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of exposure in

the actual conditions of use (taking account of all parts

of the operating cycle such as the times when the tool

is switched off and when it is running idle in addition to

the trigger time).

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr Makita M6000 Bohrschrauber zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, Makita zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres Makita M6000 Bohrschrauber in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für Makita Bohrschrauber
Weitere Anleitungen von Bohrschrauber

Häufig gestellte Fragen zu Makita M6000 Bohrschrauber

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

Makita DHP343 Bohrschrauber

Bedienungsanleitung

Makita BHP441 Bohrschrauber

Bedienungsanleitung

Makita HP003G Bohrschrauber

Bedienungsanleitung

Makita DA3000V Bohrschrauber

Bedienungsanleitung

Makita DF032D Bohrschrauber

Bedienungsanleitung

Makita DA391DWB Bohrschrauber

Bedienungsanleitung

Makita DHP484ZJ Bohrschrauber

Bedienungsanleitung

Makita DF010DSP Bohrschrauber

Verwandte Kategorien