Bedienungsanleitung Makita HM1242C Schlaghammer

Bedienungsanleitung

5

ENGLISH

Explanation of general view

1 Bit grease

2 Bit shank

3 Tool holder cap

4 Tool holder cover

5 Cut in bit shank

6 Notch in tool holder cap

7 Change ring

8 Side handle (auxiliary handle)

9 Clamp nut

10 Loosen

11 Tighten

12 Secures at eight different

positions back and forth

on the horizontal

13 Can be swung 360° on the

vertical and secured at any

desired position

14 Side handle base

15 Switch lever

16 ON

17 OFF

18 Adjusting dial

19 Power-ON indicator lamp

(green)

20 Service indicator lamp (red)

21 Screwdriver

22 Rear cover

23 Screws

24 Brush holder cap

25 Screws

26 Socket wrench

27 Crank cap

28 Hammer grease

SPECIFICATIONS

Model HM1242C

Blows per minute ...........................................950 – 1,900

Overall length ...................................................... 572 mm

Net weight............................................................... 9.3 kg

• Due to our continuing programme of research and

development, the specifications herein are subject to

change without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to enclosed safety

instructions.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety glasses

and/or face shield. It is also highly recommended

that you wear a dust mask, ear protectors and

thickly padded gloves.

2. Be sure the bit is secured in place before opera-

tion.

3. Under normal operation, the tool is designed to

produce vibration. The screws can come loose

easily, causing a breakdown or accident. Check

tightness of screws carefully before operation.

4. In cold weather or when the tool has not been

used for a long time, let the tool warm up for sev-

eral minutes by operating it under no load. This

will loosen up the lubrication. Without proper

warm-up, hammering operation is difficult.

5. Always be sure you have a firm footing. Be sure no

one is below when using the tool in high locations.

6. Hold the tool firmly with both hands.

7. Keep hands away from moving parts.

8. Do not leave the tool running. Operate the tool

only when hand-held.

9. Do not point the tool at any one in the area when

operating. The bit could fly out and injure some-

one seriously.

10. When chipping into walls, floors or wherever “live”

electrical wires may be encountered, DO NOT

TOUCH ANY METAL PARTS OF THE TOOL! Hold

the tool by the insulated grasping surfaces to pre-

vent electric shock if you chip into a “live” wire.

11. Do not touch the bit or parts close to the bit imme-

diately after operation; they may be extremely hot

and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing bit

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

This tool accepts 3/4” Hexagonal and 21/32” round shank

bits. Clean the bit shank and apply the bit grease pro-

vided to it before installing the bit. (Fig. 1)

Pull the tool holder cover down all the way. (Fig. 2-1)

With the cut in the bit shank aligned with the notch in the

tool holder cap, insert the bit into the tool holder. (Fig. 2-2)

Release the tool holder cover. It will return automatically

to its original position to secure the bit. (Fig. 2-3)

After installing, always make sure that the bit is securely

held in place by trying to pull it out.

To remove the bit, pull the tool holder cover down all the

way and pull the bit out.

Bit angle (Fig. 3)

The bit can be secured at 12 different angles. To change

the bit angle, slide the change ring forward, then turn the

change ring to change the bit angle. At the desired angle,

slide the change ring back to the original position. Then

turn the change ring slightly so that the bit will be secured

in place with a little click.

Side handle (auxiliary handle)

The side handle can be swung 360° on the vertical and

secured at any desired position. It also secures at eight

different positions back and forth on the horizontal. Just

loosen the clamp nut to swing the side handle to a desired

position. Then tighten the clamp nut securely. (Fig. 4)

The side handle also can be mounted in the rear groove

as shown in Fig. 5. Loosen the clamp nut and widen the

side handle base. Slide the side handle back to the rear

groove and secure it with the clamp nut. (Fig. 5)

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr Makita HM1242C Schlaghammer zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, Makita zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres Makita HM1242C Schlaghammer in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für Makita Schlaghämmer
Weitere Anleitungen von Schlaghämmer

Häufig gestellte Fragen zu Makita HM1242C Schlaghammer

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

Makita HM1304B Schlaghammer

Bedienungsanleitung

Makita HM1214C Schlaghammer

Bedienungsanleitung

Makita HM004G Schlaghammer

Bedienungsanleitung

Makita HM1800 Schlaghammer

Bedienungsanleitung

Makita HM1400K Schlaghammer

Bedienungsanleitung

Makita HM1317C Schlaghammer

Bedienungsanleitung

Makita HM1140C Schlaghammer

Bedienungsanleitung

Makita HM1812 Schlaghammer

Verwandte Kategorien