Bedienungsanleitung Makita FS2500 Schrauber

Bedienungsanleitung

5

For continuous operation, pull the switch trigger and then

push in the lock button.

To stop the tool from the locked position, pull the switch

trigger fully, then release it.

NOTE:

• Even with the switch on and motor running, the bit will

not rotate until you fit the point of the bit in the screw

head and apply forward pressure to engage the clutch.

Lighting up the lamps (Fig. 4)

CAUTION:

• Do not look in the light or see the source of light

directly.

To turn on the lamp, pull the trigger. Release the trigger to

turn it off.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

Reversing switch action (Fig. 5)

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

This tool has a reversing switch to change the direction of

rotation. Move the reversing switch lever to the

position (A side) for clockwise rotation or the position

(B side) for counterclockwise rotation.

Hook (Fig. 6)

The hook is convenient for temporarily hanging the tool.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing the bit

To remove the bit, first remove the locator by pulling the

lock ring away from the gear housing. Then pull the

magnetic socket bit. (Fig. 7)

To install the magnetic socket bit, insert it into the tool as

far as it will go. Then install the locator by pushing it firmly

back onto the gear housing. (Fig. 8)

OPERATION (Fig. 9)

Fit the screw on the point of the bit and place the point of

the screw on the surface of the workpiece to be fastened.

Apply pressure to the tool and start it. Withdraw the tool

as soon as the clutch cuts in. Then release the switch

trigger.

CAUTION:

• When fitting the screw onto the point of the bit, be

careful not to push in on the screw. If the screw is

pushed in, the clutch will engage and the screw will

rotate suddenly. This could damage a workpiece or

cause an injury.

• Make sure that the bit is inserted straight in the screw

head, or the screw and/or bit may be damaged.

• Hold the tool only by the handle when performing an

operation. Do not touch the metal part.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

Makita Authorized Service Centers, always using Makita

replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Phillips Insert bits

• Socket bits

• Magnetic bit holder

• Locator

For European countries only

Noise

ENG102-2

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

pA

): 83 dB (A)

Sound power level (L

WA

): 94 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection.

Vibration

ENG204-2

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Work mode: screwdriving without impact

Vibration emission (a

h

): 2.5 m/s

2

or less

Uncertainty (K): 1.5 m/s

2

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of exposure in

the actual conditions of use (taking account of all parts

of the operating cycle such as the times when the tool

is switched off and when it is running idle in addition to

the trigger time).

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr Makita FS2500 Schrauber zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, Makita zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres Makita FS2500 Schrauber in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für Makita Schrauber
Weitere Anleitungen von Schrauber

Häufig gestellte Fragen zu Makita FS2500 Schrauber

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

Makita FS4300A Schrauber

Bedienungsanleitung

Makita 6825R Schrauber

Bedienungsanleitung

Makita AR410HR Schrauber

Bedienungsanleitung

Makita FS6300X Schrauber

Bedienungsanleitung

Makita 6837 Schrauber

Bedienungsanleitung

Makita BFS441 Schrauber

Bedienungsanleitung

Makita BFL401F Schrauber

Bedienungsanleitung

Makita BFL301F Schrauber

Verwandte Kategorien