Bedienungsanleitung Makita 9565PC Winkelschleifer

Bedienungsanleitung

4

ENGLISH

Explanation of general view

1 Shaft lock

2 Lock-off lever

3 Switch lever

4 Speed adjusting dial

5 Wheel guard

6 Bearing box

7Screw

8Lever

9 Lock nut

10 Depressed center grinding

wheel/ Multi-disc

11 Inner flange

12 Lock nut wrench

13 Diamond wheel

14 Spindle

15 Exhaust vent

16 Inhalation vent

SPECIFICATIONS

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Intended use

The tool is intended for grinding, sanding and cutting of

metal and stone materials without the use of water.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

GEB033-1

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to grinder safety rules. If you use this tool unsafely

or incorrectly, you can suffer serious personal injury.

1. Safety Warnings Common for Grinding, Sanding,

Wire Brushing, or Abrasive Cutting-Off Opera-

tions:

2. This power tool is intended to function as a

grinder, sander, wire brush or cut-off tool. Read

all safety warnings, instructions, illustrations

and specifications provided with this power tool.

Failure to follow all instructions listed below may

result in electric shock, fire and/or serious injury.

3. Operations such as polishing are not recom-

mended to be performed with this power tool.

Operations for which the power tool was not

designed may create a hazard and cause personal

injury.

4. Do not use accessories which are not specifi-

cally designed and recommended by the tool

manufacturer. Just because the accessory can be

attached to your power tool, it does not assure safe

operation.

5. The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and fly apart.

6. The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories can-

not be adequately guarded or controlled.

7. The arbour size of wheels, flanges, backing pads

or any other accessory must properly fit the

spindle of the power tool. Accessories with arbour

holes that do not match the mounting hardware of

the power tool will run out of balance, vibrate exces-

sively and may cause loss of control.

8. Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad for

cracks, tear or excess wear, wire brush for loose

or cracked wires. If power tool or accessory is

dropped, inspect for damage or install an undam-

aged accessory. After inspecting and installing

an accessory, position yourself and bystanders

away from the plane of the rotating accessory

and run the power tool at maximum no-load

speed for one minute. Damaged accessories will

normally break apart during this test time.

9. Wear personal protective equipment. Depending

on application, use face shield, safety goggles

or safety glasses. As appropriate, wear dust

mask, hearing protectors, gloves and workshop

apron capable of stopping small abrasive or

workpiece fragments. The eye protection must be

capable of stopping flying debris generated by vari-

ous operations. The dust mask or respirator must be

capable of filtrating particles generated by your oper-

ation. Prolonged exposure to high intensity noise

may cause hearing loss.

Depressed center

wheel diamiter/

Spindle thread

115 mm/M14 9564PC – 9564PCV –

125 mm/M14 9565PC – 9565PCV –

150 mm/M14 – 9566PC – 9566PCV

No load speed (n

o

) / Rated speed (n)

11,500 min

–1

10,000 min

–1

2,800 – 11,500 min

–1

4,000 – 10,000 min

–1

Overall length 307 mm 307 mm 307 mm 307 mm

Net weight 1.9 kg 1.9 kg 1.9 kg 1.9 kg

Safety class /II

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr Makita 9565PC Winkelschleifer zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, Makita zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres Makita 9565PC Winkelschleifer in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für Makita Winkelschleifer
Weitere Anleitungen von Winkelschleifer

Häufig gestellte Fragen zu Makita 9565PC Winkelschleifer

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

Makita 9557NBR Winkelschleifer

Bedienungsanleitung

Makita GA9071 Winkelschleifer

Bedienungsanleitung

Makita GA5041C Winkelschleifer

Bedienungsanleitung

Makita GA9070 Winkelschleifer

Bedienungsanleitung

Makita BGA402 Winkelschleifer

Bedienungsanleitung

Makita DGA508 Winkelschleifer

Bedienungsanleitung

Makita GA9050 Winkelschleifer

Bedienungsanleitung

Makita DGA506 Winkelschleifer

Verwandte Kategorien