Bedienungsanleitung Kampa Air Shelter 400 Zelt

Bedienungsanleitung

EN

4445103460 5

Setting up the shelter

!

A

I

Keep the following tips in mind while setting up the shelter:

• The figures provide a general overview of the set-up. The actual set-up

will vary slightly based on the model of shelter.

• Get help. The set-up is easier with more people.

• After standing the shelter upright, check the corner pegs and re-peg

if necessary. The groundsheet on the inside should be taut and in a

rectangular shape.

• Peg the guy lines so that the shelter is under tension without distorting

the shape.

• Check the guy lines from time to time to ensure adequate tension, if

necessary use the runners to adjust.

Set up the shelter as follows:

1. To protect the shelter from dirt and damage, lay down a groundsheet

or footprint before unpacking.

2. Unpack the shelter.

3. Separate and identify the different components.

4. Proceed as shown to set up the shelter (fig. 1, page 3 to fig. 6,

page 3).

Dismantling the shelter

A

1. Reverse the set up procedure.

2. Push the poles out of the sleeves, do not pull.

3. Ensure that all parts are clean before packing in the carry bag.

4. If the shelter is wet or damp, dry fully as soon as possible.

Cleaning and maintenance

A

1. If necessary, clean the product with clean water and a soft brush.

2. Apply impregnation against water and UV radiation before each trip.

Storing the shelter

I

1. Clean the shelter.

2. Air fully and ensure the shelter is totally dry before packing away.

3. Store in a well ventilated dry place.

Troubleshooting

I

Repairing a puncture in the air pole

If the air pole loses air, proceed as follows:

1. Unzip the outer sleeve holding the air pole.

2. If installed, close isolation valves.

3. Remove the air pole.

4. Deflate the air pole.

5. Unzip the protective sleeve to expose the inflatable tube.

6. Blow some air into the inflatable tube.

7. Submerge the tube in water.

8. Locate the puncture.

9. Use repair tape and repair solution to seal the hole.

10. Zip the inflatable tube back into the protective sleeve.

11. Zip the air pole back into the outer sleeve.

CAUTION! Risk of injury and material damage

• Do not use any type of compressor designed to inflate

car tires.

• Only inflate the air poles into the green zone of the

pressure gauge of the supplied hand pump (7 –

8 psi/0.48 – 0.55 bar).

NOTICE! Material damage

Do not open or close the zippers by force.

NOTE

• The shelter comes with general purpose pegs. These

will be suitable for many sites but for some types of

ground special pegs will be needed. Ask your dealer.

• Drive the pegs at a 45° angle away from the shelter into

the ground.

• Peg each guy line in-line with the seam it starts from.

NOTICE! Material damage

Do not use force when dismantling the shelter. Otherwise

you might damage any material.

NOTICE! Damage hazard

• Do not use sharp or hard objects or cleaning agents for

cleaning.

• Do not use alcohol based materials, chemicals, soap

and detergents for cleaning.

• Remove bird droppings and tree resin as soon as

possible to avoid permanent damage to the material.

NOTE

• Fully set up the shelter for cleaning.

• Choose a sunny day for cleaning to ensure the material

will dry thoroughly.

NOTE

• During first exposure to water there may be some

moisture at the seams. Through this moisture the threads

will swell and fill the holes that are created in the sewing

process.

• A fully equipped spare parts kit should include:

– Waterproofer

– Repair tape and repair solution

– Silicone spray for the zippers

– Spare pegs

Problem Solution

Shelter only inflates with difficulties ➤ Check that the valve is fully screwed

into the air pole.

➤ Check if the inflation tube is twisted at

the valve.This may be indicated by

noise. Untwist the inflation tube

Air leak ➤ Check that the valve is fully screwed

into the air pole and the ring seal is in

place.

➤ Check that the cap of the valve is done

up tightly.

➤ Check for punctures, see chapter

“Repairing a puncture in the air pole”

on page 5.

Water leak

➤ Check for leaky seams, damaged

tapings and moist areas.

➤ If you find any leaks, apply seam

sealant.

Rip in the fabric

➤ Use repair tape to seal the fabric.

➤ Have repairs carried out by an

authorized specialist.

KampaAirShelter200-300-400_IOM_4445103460_EMEA16_20xx-xx-xx.book Seite 5 Montag, 4. Oktober 2021 12:30 12

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr Kampa Air Shelter 400 Zelt zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, Kampa zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres Kampa Air Shelter 400 Zelt in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für Kampa Zelte
Weitere Anleitungen von Zelte

Häufig gestellte Fragen zu Kampa Air Shelter 400 Zelt

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

Kampa Hayling 4 Zelt

Bedienungsanleitung

Kampa Brighton 2 Zelt

Bedienungsanleitung

Kampa Brean 4 Zelt

Bedienungsanleitung

Kampa Air Shelter 300 Zelt

Bedienungsanleitung

Kampa Brean 4 Air Zelt

Bedienungsanleitung

Kampa Action AIR Zelt

Bedienungsanleitung

Kampa Brighton 3 Zelt

Bedienungsanleitung

Kampa Croyde 6 Zelt

Verwandte Kategorien