Bedienungsanleitung Hikoki WR 14VE Schlagschrauber

Bedienungsanleitung

4

English

1. Switch operation (Fig. 4)

○ When the switch trigger (4) is depressed, the tool

rotates. When the trigger is released, the tool stops.

○ The rotational speed can be controlled by varying the

amount that the switch trigger (4) is pulled. Speed is low

when the switch trigger is pulled slightly and increases

as the switch trigger is pulled more.

2. Switching tightening mode (see Fig. 2)

Each press of mode switch (2) will change the impact

rate.Switch(4)mustbeswitchedOFFwhenconducting

this operation. Use A or B for light tasks, and C or D for

heavy tasks.

3. The protection function

To protect the tool, the protection function will be

activated, automatically shutting down the unit in the

event of any problems. (Table 1)

Table 1

Mode Indicator Lamp (3)

(see Fig. 2)

Cause of Shutdown

Flashing

Fastrepeatedashes

Flashesonandowith

0.1-second intervals

Automatic shutdown

initiated by excessive

load (*1)

Slowrepeatedashes

Flashesonandowith

1-second intervals

Automatic shutdown

initiated due to sensor

detection trouble (*2)

Flashing during mode operation

Automatic shutdown

initiatedduetothetool’s

internal temperature

exceedingthespecied

temperature level (*3)

Automatic shutdown

initiated due to

approximately 5 minutes

of continuous no-load

operation (*4)

*1 Excessive load protection function

For excessive load conditions, the tool will shutdown to

prevent damage.

Discontinue the heavy load task and press mode switch

(2) to reset the tool.

*2 Control monitoring function

Press mode switch (2) to reset the tool.

Continual occurrences of this situation may be the result

of damage to the tool.

*3 Increased temperature protection function

Automatic shutdown is activated to prevent damage

from high temperatures.

 The tool’s internal temperature will increase for tasks

involving the use of large currents of electricity, or when

used in high temperature environments.

Please allow the tool to rest for 10 to 15 minutes before

continuing a task.

*4 Continuous operation prevention function

Shutdown will occur in the event of continuous operation

whiletheswitchremainsON.

MAINTENANCE AND INSPECTION

1. Inspecting the socket

 Aworn ordeformed hexor asquare-holed socketwill

notgiveanadequatetightnesstothettingbetweenthe

nutoranvil,consequentlyresultinginlossoftightening

torque.Payattentiontowearofsocketholesperiodically,

and replace with a new one if needed.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Replacing supply cord

If the replacement of the supply cord is necessary, this

has to be done by the manufacturer of this agent in order

to avoid a safety hazard.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country specic regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATEfoundattheendofthisHandlinginstruction,

toaHiKOKIAuthorizedServiceCenter.

IMPORTANT

Correct connection of the plug

The wires of the main lead are coloured in accordance

with the following code:

Blue:—Neutral

Brown: — Live

As the colours of the wires in the main lead of this tool may

not correspond with the coloured markings identifying the

terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black. The wire

coloured brown must be connected to the terminal marked

with the letter L or coloured red. Neither core must be

connected to the earth terminal.

NOTE:

This requirement is provided according to BRITISH

STANDARD2769:1984.

Therefore, the letter code and colour code may not be

applicabletoothermarketsexceptTheUnitedKingdom.

Information concerning airborne noise and vibration

The measured values were determined according to

EN62841anddeclaredinaccordancewithISO4871.

Measured A-weighted sound power level: 98 dB (A)

Measured A-weighted sound pressure level: 111 dB (A)

UncertaintyK:3dB(A).

Wear hearing protection.

Vibration total values (triax vector sum) determined

accordingtoEN62841.

Impact tightening of fasteners of the maximum capacitiy of

the tool:

Vibration emission value

a

h

= 13.2 m/s

2

UncertaintyK=1.5m/s

2

The declared vibration total value has been measured in

accordance with a standard test method and may be used

for comparing one tool with another.

It may also be used in a preliminary assessment of exposure.

0000Book_WR14VE.indb 4 2019/03/05 16:45:10

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr Hikoki WR 14VE Schlagschrauber zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, Hikoki zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres Hikoki WR 14VE Schlagschrauber in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für Hikoki Schlagschrauber
Weitere Anleitungen von Schlagschrauber

Häufig gestellte Fragen zu Hikoki WR 14VE Schlagschrauber

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

Hikoki WR 14DSDL Schlagschrauber

Bedienungsanleitung

Hikoki WR 18DSDL Schlagschrauber

Bedienungsanleitung

Skil 3210 CA Schlagschrauber

Bedienungsanleitung

Skil 3265 JA Schlagschrauber

Bedienungsanleitung

AEG BSS18SRA38BL0 Schlagschrauber

Bedienungsanleitung

Skil 3210 GA Schlagschrauber

Bedienungsanleitung

Makita TW009G Schlagschrauber

Bedienungsanleitung

Makita DTW181 Schlagschrauber

Verwandte Kategorien