Bedienungsanleitung FERM TDM1006 Tischbohrmaschine

Bedienungsanleitung

Ferm 53

ELECTRICAL INSTALLATION

The machine is provided with an electrical installation,

which meets the standards. Repairs may only be carried

out by a recognised professional.

The machine is provided with a zero voltage switch.

After the tension drops the machine will not start to

run automatically for safety reasons. The machine must be

switched on again.

Electrical safety

Always check that the power supply corresponds to the

voltage on the rating plate.

Replacing cables or plugs

Immediately throw away old cables or plugs when they

have been replaced by new ones. It is dangerous to insert

the plug of a loose cable in the wall outlet.

Using extension cables

Only use an approved extension cable suitable for the

power input of the machine. The minimum conductor

size is 1.5 mm

2

. When using a cable reel always unwind

the reel completely.

ASSEMBLY

Fig.B

• Place the footplate (13) in the correct position.

• Fasten the column (11) with the bolts supplied (12) to

the footplate.

• Now slide the table holder (10) with the table over

the column (11). With the fastening handle (6) the

table is fastened into the desired position.

• Now you can assemble the machine casing (7) and

lock with the locking pins (8).

• Since the drill spindle is greased in the factory, it is

advisable to run in the machine for approximately 15

minutes at the lowest speed (Fig. B).

Before you push the chuck with pin into the drill

spindle, the inside of the chuck must be completely

grease-free!

SETTING UP THE BENCH DRILL

Before use the drill must be mounted on a fixed base. The

footplate (13) has therefore been provided with drilling

holes. By means of screws the footplate can be fixed to

the base in this place. If it is mounted on a wooden board,

sufficiently large washers must be used on the opposite

side, so that the bolts are not pushed into the wood and

the machine cannot become loose.

The fastening screws may be fastened so far that

the footplate is not under tension or deformed.

When the tension is too high there is a risk of breakage.

ADJUSTING THE NUMBER OF REVOLU-

TIONS OF THE DRILL SPINDLE

Fig.C

The different revolutions of the drill spindle can be adjus-

ted by shifting the V-belt into the belt drive. The machine

is protected by a safety switch so that the machine is

automaticly switched off when opening the casing

The V-belt is shifted as follows:

• Open the V-belt cover (14) by loosen the screw on

the right side of the cover.

• Loosen the fastening button (18) and slide the engine

in the direction of the machine head, upon which the

V-belt is released.

• Shift the V-belt according to the table on the inside of

the V-belt cover.

• Tension the V-belt again by pushing the engine plate

(17) to the back. Then the tensioning device is faste-

ned with the fastening button (18).

• Close the V-belt cover and the machine is ready again

for use.

Keep the V-belt cover closed during use.

4 Ferm

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr FERM TDM1006 Tischbohrmaschine zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, FERM zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres FERM TDM1006 Tischbohrmaschine in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für FERM Tischbohrmaschinen
Weitere Anleitungen von Tischbohrmaschinen

Häufig gestellte Fragen zu FERM TDM1006 Tischbohrmaschine

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

FERM TDM1008 Tischbohrmaschine

Bedienungsanleitung

FERM TDM1026 Tischbohrmaschine

Bedienungsanleitung

FERM TDM1007 Tischbohrmaschine

Bedienungsanleitung

FERM TDM1011 Tischbohrmaschine

Bedienungsanleitung

FERM TDM1027 Tischbohrmaschine

Bedienungsanleitung

FERM TDM1021 Tischbohrmaschine

Bedienungsanleitung

FERM TDM1025 Tischbohrmaschine

Bedienungsanleitung

FERM TDM1012 Tischbohrmaschine

Verwandte Kategorien