Bedienungsanleitung Casals VSC65 Kreissäge

Bedienungsanleitung

Once you have nished using the appliance:

- Stop the appliance by releasing the on/off switch.

Maintenance and care

WARNING! Always unplug the machine before carrying

out work on it.

- Checking the saw blade: deposits of resin and glue

on the saw blade cause inefcient cutting. To avoid them,

always clean the blade immediately after use.

- Inspect the mounting screws: regularly inspect all the

mounting screws and ensure they are rmly tightened.

Should any screw be loose, tighten it immediately. Failure

to do so could put you at serious risk.

- Motor maintenance: always take the greatest care

over this and make sure that the motor winding is not

damaged and does not become wet with oil or water.

- The vents should always be kept clean and free of

obstacles.

- Clean the machine thoroughly after each use. Blast the

motor regularly with compressed air.

- Check that the mains lead is in good condition. If it

is not, take it to an Ofcial Service Centre to have it

replaced.

Cleaning

- Disconnect the appliance from the mains and allow it

to cool before undertaking any cleaning task.

- Clean the electrical equipment and the mains

connection with a damp cloth and dry. DO NOT

IMMERSE IN WATER OR ANY OTHER LIQUID.

- Clean the equipment with a damp cloth with a few

drops of washing-up liquid and then dry.

- Do not use solvents, or products with an acid or base

pH such as bleach, or abrasive products, for cleaning

the appliance.

- Do not let water or any other liquid get into the air

vents to avoid damage to the inner parts of the

appliance.

- Never submerge the appliance in water or any other

liquid or place it under running water.

- If the appliance is not in good condition of cleanliness,

its surface may degrade and inexorably affect the

duration of the appliance’s useful life and could

become unsafe to use.

- CAUTION: There is a risk of re if the appliance’s

cleaning is not done according to these instructions.

Supplies

- Always use original supplies, designed specically

for your appliance model.

- These supplies are available in specialist shops.

6

soon as blade enters the material, the lower guard must

be released. For all other sawing, the lower guard should

operate automatically.

- Always observe that the lower guard is covering the

blade before placing saw down on bench or oor. An

unprotected, coasting blade will cause the saw to walk

backwards, cutting whatever is in its path. Be aware of the

time it takes for the blade to stop after switch is released.

Product description and Specications

Description

A

HM saw blade

B Spindle blocking button

C Mobile blade guard

D Saw blade setting disc

E Disc setting screw

F Depth setting wing nut

G Lateral stop setting wing nut

H Safety push button switch

I On-/off switch

J Angular cutting wing nut

K Cutting line guide

L Sawdust extraction

M Lateral Stop

Instructions for use

Before use:

- Make sure that all the product’s packaging has been

removed.

- Ensure that the voltage indicated on the rating label

matches the mains voltage before plugging in the

appliance.

- Prepare the appliance according to the function you

wish to use:

Fitting the disc

- Unplug the appliance from the mains before replacing

any accessory.

WARNING! : Always unplug the machine before carrying

out any work on it.

CAUTION: Do not use bent or cracked blades or high-

speed steel blades. Do not use saw blades that do

not conform to the specications contained in these

instructions.

WARNING! Never press the blocking button B when

the machine is running. The shaft must have stopped

completely before the blocking button B is pressed.

1. Move the mobile guard (C) backwards and hold

it in place.

2. To loosen or tighten screw (E), block the screw

press by pushing block button (B).

3. Loosen the screw (E) and remove the setting

disc (D).

4. Fit the saw blade and tighten with the setting disc

(D) and the screw (E).

4.1 To adapt saw discs with a 30mm hole diameter,

rst t the washer that corresponds to the diameter

of the saw disc you are using, next the saw disc

and screw them into place with fastening disc D and

screw E.

5. Before tting the new blade, make sure the

surfaces in contact with the setting discs are clean.

(The arrow printed on the xed guard of the machine

indicates the cutting direction of the teeth).

6. Once the disc is tted, check that the blocking

button (B) has returned to its original position due to

movement of the incorporated spring.

- In order to remove disc, follow the same steps as

indicated previously but in reverse order.

Dust extraction Assembly

- Always use the appliance with the dust collector

connected, inhaling dust is harmful to your health.

- Connect the vacuum aspirator suction tube to the dust

extraction adaptor (L)

Use:

Cutting depth setting

- To adjust the cutting depth, loosen the wing nut (F) and

move the base upwards or downwards. The scale printed

on the base indicates the cutting depth

Cutting angle setting

It can cut vertically and with an inclination of up to 45º.

The angle is adjusted by loosening the wing nut (J) and

according the scale printed on the base.

Cutting indication

The notch K is used as a cutting indication with the blade in

a vertical position or 45º. It is advisable to make test cuts.

Lateral stop adjustment

For parallel cutting, use the lateral stop (M). Cutting width

is adjusted with the scale or according to the plotting.

Tighten the wing nut (G) to work with the lateral stop.

- Connect the appliance to the mains.

- Press the locking button (H), and squeeze the trigger in

the on/off switch (I). When the on/off switch is released, the

machine stops.

Bewertung

Mehr zu diesem Bedienungsanleitung

Wir verstehen, dass es schön ist, ein gedrucktes Bedienungsanleitung für Ihr Casals VSC65 Kreissäge zu haben. Sie können das Bedienungsanleitung jederzeit von unserer Website herunterladen und selbst ausdrucken. Wenn Sie ein Originalhandbuch wünschen, empfehlen wir Ihnen, Casals zu kontaktieren. Möglicherweise können sie ein Originalhandbuch bereitstellen. Suchen Sie das Bedienungsanleitung Ihres Casals VSC65 Kreissäge in einer anderen Sprache? Wählen Sie auf unserer Homepage Ihre bevorzugte Sprache und suchen Sie nach der Modellnummer, um zu sehen, ob wir sie verfügbar haben.

Spezifikationen

Alle Anleitungen für Casals Kreissägen
Weitere Anleitungen von Kreissägen

Häufig gestellte Fragen zu Casals VSC65 Kreissäge

Unser Support-Team sucht nach nützlichen Produktinformationen und beantwortet Ihre häufig gestellten Fragen. Sollte Ihnen ein Fehler bei den häufig gestellten Fragen auffallen, teilen Sie uns dies bitte anhand unseres Kontaktformulars mit.

Verwandte Produkte

Bedienungsanleitung

Casals CCS190L Kreissäge

Bedienungsanleitung

Metabo KT 18 LTX 66 BL Kreissäge

Bedienungsanleitung

Vonroc CS502AC Kreissäge

Bedienungsanleitung

My Project MOY-YFT01 Kreissäge

Bedienungsanleitung

Vonroc S_CS503AC Kreissäge

Bedienungsanleitung

Probuilder 43653 Kreissäge

Bedienungsanleitung

Parkside IAN 279503 Kreissäge

Bedienungsanleitung

Sthor 79257 Kreissäge

Verwandte Kategorien